MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 336

Страница: 336 / 385

ACTIVATION screen page

This screen page is used to delete errors in the

control unit memory and to activate some systems

controlled by the control unit.

ACTIVATION

Characteristic

Value/example

Unit of

measure

ment

Notes

Front brake bleeding procedure

Useful in case of lever sponginess although the

bleeding has been done as in a regular braking

system

Rear brake bleeding procedure

Useful in case of lever sponginess although the

bleeding has been done as in a regular braking

system

ABS warning light

During the test the warning light stays on

Ambient parameter error reading (1)

The ambient parameters are 4: Number of error

detections, Operation cycles from the last detec-

tion, Battery voltage, Speed.

Ambient parameter error reading (2)

Number of error detections: number of times the

error has been detected by the control unit;

Ambient parameter error reading (3)

for example, if it indicates 2, it means that the error
has been detected (ATT), then it has not been de-

tected for a while (sent to the MEM) and then it

has been detected again.

Ambient parameter error reading (4)

Operation cycles from the last reading: a cycle is

counted if the following occurs: key ON and speed

over 20 km/h.

Ambient parameter error reading (5)

If for example 5 is shown, it means that the last

time the error has been measured was 5 cycles

ago.

Error clearing (1)

Press "enter" to transfer errors from the memory

(MEM) to the historical record (STO).

Error clearing (2)

In the next connection between Navigator and the
control unit, the historical errors (STO) are no lon-

ger shown.

ERRORS screen page

This screen page displays any errors detected in

the vehicle (ATT) or stored in the control unit

(MEM) and you can check that the cancellation of

error (STO) has taken place.

Braking system

Stelvio 1200 NTX MY11

BRAK SYS - 336

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

Похожие инструкции для Stelvio 1200 MY11 2011

Бренды по названию

Популярные бренды

MOTO GUZZI Stelvio 1200 MY11 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

Похожие инструкции для Stelvio 1200 MY11 2011

Бренды по названию

Популярные бренды