MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 111

Страница: 111 / 385

In case of recovery, this value is set by the control unit.

NAVIGATOR: ERRORS

engine temperature sensor P0115

- open circuit, shorted to positive / shorted to negative.

Error cause

•

If the circuit is open, shorted to positive: excessive voltage has been detected at PIN 5 of

connector A (BROWN).

•

If shorted to negative: voltage equal to zero has been detected at PIN 5 of the BROWN

connector.

Troubleshooting

•

If the circuit is open, shorted to positive: check sensor connector and Marelli control unit

connector; if not OK, restore cable harness; if OK, check sensor continuity; if it is not OK,

replace the sensor; if it is OK, check continuity between PIN 5 of the BROWN connector and

PIN 2 of sensor: restore cable harness if there is not continuity; if it is OK, reconnect the

control unit connector and, with key set to key ON, check the continuity between the sensor

connector PIN 1 and the vehicle ground connection: if there is not continuity, restore the

cable harness; if there is continuity, it means that the cause of the error is that the cable is

shorted to positive and now the cable harness between the BROWN PIN 5 and PIN 2 of the

sensor should be restored. If the air temperature sensor error is displayed at the same time,

this means that the grey cable common for both sensors is shorted to positive.

•

If shorted to negative, check sensor correct resistance: if resistance is null, replace the sen-

sor; if resistance is correct, it means that the orange cable has ground connection: restore

the cable harness.

NOTES

No error is detected if the sensor does not work correctly or the control unit connector

or sensor terminals are rusty: then check through Navigator if the temperature indicated is the

same as the engine temperature. Check also that the sensor electrical characteristics are ob-

served: replace the sensor if not OK; if it is OK, check the sensor connector and the Marelli

control unit connector

Stelvio 1200 NTX MY11

Electrical system

ELE SYS - 111

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

MOTO GUZZI Stelvio 1200 MY11 2011, Руководство по обслуживанию станции, Страница: 111 / 385

Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы: