MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 224

Страница: 224 / 385

•

Screw two screws in the threaded

holes of the timing system upper gear.

•

Rotate the camshaft so that its pin is

aimed towards the hole in the timing

system chain.

•

Place the gear in the chain.

•

On the left camshaft pin, fit the hole

marked with the letter "L" of the timing

system gear.

•

Block the left chain tensioner hole with

screw and washer.

•

Rotate the crankshaft clockwise by

270° from the timing system side so

that the right cylinder piston reaches

the TDC; lock crankshaft rotation.

•

Also determine the thickness of the

gasket for the right cylinder, to be fitted

between the head and the cylinder as

described in the section: Shimming

system.

•

Place the two dowel pins.

•

Fit the gasket with the correct thick-

ness between the head and the cylin-

der.

•

Fit the right cylinder head.

•

Unscrew and remove the right chain

tensioner cap.

Engine

Stelvio 1200 NTX MY11

ENG - 224

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

Похожие инструкции для Stelvio 1200 MY11 2011

Бренды по названию

Популярные бренды

MOTO GUZZI Stelvio 1200 MY11 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

Похожие инструкции для Stelvio 1200 MY11 2011

Бренды по названию

Популярные бренды