MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 115

Страница: 115 / 385

•

shorted to positive: disconnect the probe connector and check the sensor correct resistance:

replace the sensor if not OK; if it is OK, restore the cable harness.

•

circuit is open, shorted to negative: check the continuity from probe connector (PIN 3 and

4) towards the probe: if not OK, replace the probe; if it is correct, check the sensor connector

and the Marelli control unit connector. If not OK, restore. If OK, and with key set to ON and

sensor connector disconnected, check if there is battery voltage at PIN 4: se non ok verificare

cavo rosso/nero (lato cablaggio) tra connettore sonda e relè iniezione secondario (n°37 dello

schema elettrico, posizione lato sinistro anteriore del motociclo, primo relè a sinistra vicino

alla bobina, VERIFICARE comunque l'identificazione del relè con il colore dei cavi), se pre-

senti anche errori bobine e iniettori verificare il relè stesso e la sua linea di eccitazione e

potenza; if there is voltage at PIN 4, check the white cable ground insulation, cable harness

side (PIN 3): if it is not OK, restore the cable harness. If OK, check continuity of the white

cable, cable harness side (between PIN 3 of the sensor connector and PIN 11 of the BLUE

connector) and restore the cable harness.

LOGIC ERRORS

Left lambda sensor P0134-

voltage without variation.

Error cause

•

An abnormal behaviour of the voltage at PIN 22 of the BLUE connector has been detected:

the voltage, that should vary over time, keeps a constant value instead.

Troubleshooting

•

check circuit continuity of the lambda sensor connector (PIN 1 PIN2) toward the probe:

replace the probe if there is no continuity; if there is continuity, check the sensor connector

and the Marelli control unit connector: If not OK, restore. If OK, check continuity between

the BLUE connector PIN 22 and PIN 32 and restore the cable harness.

ELECTRICAL ERRORS

Right lambda sensor P0136

- Shorted to positive.

Error cause

•

Excessive voltage (battery voltage) has been detected at PINS 21 and 31 of the BLUE

connector.

Troubleshooting

•

shorted to positive: con chiave ON, scollegare il connettore del sensore e misurare la ten-

sione al PIN 1 lato cablaggio (cavo viola/giallo): if there is voltage (5 or 12 V), restore the

cable harness; it there is no voltage, measure voltage at PIN 2, cable harness side, (brown

cable) and if there is voltage, restore the cable harness; if there is no voltage, replace the

lambda sensor.

Right lambda sensor heating P0141

- shorted to positive / open circuit, shorted to negative.

Error cause

Stelvio 1200 NTX MY11

Electrical system

ELE SYS - 115

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

Похожие инструкции для Stelvio 1200 MY11 2011

Бренды по названию

Популярные бренды

MOTO GUZZI Stelvio 1200 MY11 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

Похожие инструкции для Stelvio 1200 MY11 2011

Бренды по названию

Популярные бренды