MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 124

Страница: 124 / 385

the sensor. If the circuit is open, it means that the brown/purple cable from PIN 1 of the

sensor to PIN 33 of the BLUE connector is shorted to ground: restore the cable harness

Side stand sensor

Function

It tells the side stand position to the control unit.

Operation / Operating principle

If the gear is engaged and the side stand is unfolded, and therefore the circuit is open, the control unit

does not enable vehicle start-up or shuts off the engine if it is rotating.

Level in electrical circuit diagram:

Start-up enabling switches

Location:

•

sensor: on side stand supporting plate

•

Connector: left side, near the starter motor

Electrical characteristics:

•

Side Stand Up: closed circuit (continuity)

•

Side Stand Down: open circuit (infinite resistance)

Pin-out:

1. Ground connection

2. Voltage 12 V (brown, sensor side)

NAVIGATOR: STATUSES

Side stand

Example value:

retracted / extended

DIAGNOSIS

•

Indication on Navigator always EXTENDED: check the side stand sensor connector and the

ECU connector: se non ok ripristinare, se ok scollegare i due terminali dal sensore e verifi-

care continuità a massa del PIN 1 (grigio lato cablaggio): if there is not continuity, restore

the cable harness; if there is, check continuity of the green/brown cable: if it is not OK,

restore; if OK, replace the sensor.

•

Indication on Navigator always RETRACTED: disconnect the terminals from the sensor and

check if there is continuity between the two PINS, with stand down: if there is continuity,

replace the sensor; if the circuit is open, it means that the brown/green cable (cable harness

side) from PIN 2 of the sensor to PIN 38 of the BLUE connector is shorted to ground: restore

the cable harness.

Bank angle sensor

(if applicable)

Electrical system

Stelvio 1200 NTX MY11

ELE SYS - 124

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

MOTO GUZZI Stelvio 1200 MY11 2011, Руководство по обслуживанию станции, Страница: 124 / 385

Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы: