MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 261

Страница: 261 / 385

•

Make sure there are no errors in the

control unit; otherwise, solve them and

repeat the procedure.

•

Make sure the left throttle is fully in.

DO NOT TOUCH THE THROTTLE ABUTMENT SCREW OR
THE THROTTLE BODY MUST BE REPLACED. CHECK
THAT THE THROTTLE RETURN CABLE IS NOT TAUT.

•

The instrument should display the adjustable parameters screen page.

•

Autodetect the throttle position.

•

Turn the key to "OFF" and leave it for

at least 30 seconds.

•

Turn the key back to "ON" and restore

the instrument session.

•

Check that the "Throttle" value reading

is 4.7 +/- 0.2°. If the value is incorrect,

replace the control unit and repeat the

procedure from the start.

•

Completely close the two by-pass

screws on the throttle bodies.

•

Start the engine.

•

Take the engine to the prescribed tem-

perature: 60 °C (140 °F).

•

Make the engine rev at 2000/3000 rpm

and with the vacuometer check that the

difference between the two pressures

is 1 cm Hg (1.33 kPa) maximum.

If this condition is detected:

•

take the engine back to idle and check

the depression values so that they are

aligned between the two cylinders.

Otherwise, open only the screw with

higher depression, using the by-pass

screws, to compensate.

Stelvio 1200 NTX MY11

Power supply

P SUPP - 261

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

MOTO GUZZI Stelvio 1200 MY11 2011, Руководство по обслуживанию станции, Страница: 261 / 385

Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы: