MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 351

Страница: 351 / 385

REPLACE THE ABS CONTROL UNIT

VEHICLE PREPARATION

•

Connect the bleed bottle to the bleed

screws of the front and rear callipers

and open it.

•

Fully press down the lever and the

brake pedal and fix them into position

with the respective locking devices.

•

Close the bleed screws of the front and

rear callipers and remove the bleed

bottle.

•

Remove the damaged ABS control

unit.

Note: First of all, detach the brake pipes that

go from the ABS control unit to the brake pump

(1-4) and immediately seal the opened unions

of the ABS control unit with protective caps.

Afterwards, remove pipes (2-3) that go from the

ABS control unit to the brakes and also seal

these unions with protective caps.

•

Install the new ABS control unit, previ-

ously filled up.

•

So that the brake fluid remains in the

ABS control unit, first remove the pro-

tective caps of the braking circuit un-

ions and connect the respective pipes.

Once all the braking circuits have been con-

nected, remove the protective caps from the

braking pump unions and connect the braking

pump pipes to the ABS control unit.

•

Unlock the lever and the brake pedal.

•

Remove the reservoir cap and fill it with

new brake fluid up to the reference

"MAX".

CAUTION

PERFORM THE REGULAR BRAKING SYSTEM BLEEDING,
AS DESCRIBED AT THE END OF THE CHAPTER.

•

Always fill the reservoir up to the reference "MAX" and refit the cap.

Stelvio 1200 NTX MY11

Braking system

BRAK SYS - 351

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

Похожие инструкции для Stelvio 1200 MY11 2011

Бренды по названию

Популярные бренды

MOTO GUZZI Stelvio 1200 MY11 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

Похожие инструкции для Stelvio 1200 MY11 2011

Бренды по названию

Популярные бренды