MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 100

Страница: 100 / 385

Checking the stator

Single-phase generator with regulated voltage

Maximum load 40A (550W)

Charging voltage 14.2 - 14.8 V (5000 rpm)

Start-up system check

pick-up input about 100 A

level indicators

Petrol pump:

Input: 3.5 A (to be measured between pins 1 and

2 with 12V voltage)

Fuel level sensor:

Resistance (to be measured between pins 3 and

250-300 Ohm with fuel level equal to 0 litre

100 Ohm with fuel level equal to 11.25 litres (20.43

pt)

10-20 Ohm with fuel level equal to 22.5 litres

(40.86 pt)

The low fuel warning light turns on with values over

230 Ohm.

In case there is anomaly on the fuel probe, the low fuel warning light flashes on the instrument panel.

The alarm warning light on the instrument panel does not light up and the word Service is not displayed.

Electrical system

Stelvio 1200 NTX MY11

ELE SYS - 100

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

MOTO GUZZI Stelvio 1200 MY11 2011, Руководство по обслуживанию станции, Страница: 100 / 385

Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы: