MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 199

Страница: 199 / 385

Removing the valves

•

Remove the head.

•

Place the special tool on the upper cap

and at the centre of the head of the

valve to be removed.

Specific tooling

10.90.72.00

Tool for valve removal and refitting

AP9100838

Tool for valve pressure plate

•

Tighten the tool screw until fitted, and

then hit the tool head (where the upper

cap works) with a mallet so that the two

cotters (1) get detached from the upper

cap (2).

•

Once the two cotters (1) are detached,

screw these cotters until they can be

slid off the valve seats; unscrew the

tool and remove it from the head.

•

Slide off the upper cap (2).

•

Remove the spring (3).

•

Remove the lower cap (5) and the

valve guide oil seal (4), if necessary.

•

Remove the valve (6) from inside the

head.

Checking the valve guides

Use a punch to extract the valve guides from the heads.

The valve guides should be replaced only if the clearance between them and the stem cannot be elim-

inated by simply replacing the valves.

To refit the valve guides on the head, follow this procedure:

•

Heat the head in an oven at approximately 60°C (140°F).

•

Lubricate the valve guide.

•

Fit the circlips.

•

Press a punch with the valve guides.

Stelvio 1200 NTX MY11

Engine

ENG - 199

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

Похожие инструкции для Stelvio 1200 MY11 2011

Бренды по названию

Популярные бренды

MOTO GUZZI Stelvio 1200 MY11 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

Похожие инструкции для Stelvio 1200 MY11 2011

Бренды по названию

Популярные бренды