MOTO GUZZI Stelvio 1200 MY11 2011 Скачать руководство пользователя страница 125

Страница: 125 / 385

Function

it tells the vehicle position to the control unit.

Operation / Operating principle

When the sensor is inverted, the circuit is closed

to ground: when the Marelli control unit detects this

earthing, it disables the fuel pump circuit and the

engine start-up circuit via the injection relay.

Level in electrical circuit diagram:

Start-up ena-

bling switches.

Location:

•

Sensor: under the saddle, right side

•

Connector: near the sensor

Electrical characteristics:

•

Sensor in vertical position: open circuit

(resistance: 62 kOhm)

•

Sensor inverted: closed circuit (resist-

ance below 0.5 kOhm)

Pin-out:

1. Voltage 12V

2. Ground connection

NAVIGATOR: STATUSES

Fall sensor

Example value:

Normal / Tip over

DIAGNOSIS

•

Indication on Navigator always Normal, even when the sensor is inverted: disconnect the

connector and, with sensor inverted, check if there is continuity between the two PINS of

the sensor: if there is no continuity, replace the sensor; if there is, check the connector. If

not OK, restore the cable harness; if OK, check continuity to ground of PIN 2: if there is no

continuity, restore the cable harness; if there is, with key set to KEY ON, check if there is

12V voltage at PIN 1. If there is not, check the Marelli control unit connector (PIN 35 of the

BLUE connector)

•

Indication on Navigator always Tip over: disconnect the connector and check if there is

continuity between the two PINS when the sensor is in vertical position: if there is continuity,

replace the sensor; if there is not, it means that, with key set to KEY ON, there is no 12V

voltage at PIN 1: restore the cable harness whose pink/yellow cable will be shorted to ground

Stelvio 1200 NTX MY11

Electrical system

ELE SYS - 125

Содержание Stelvio 1200 MY11 2011


































































































































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы:

MOTO GUZZI Stelvio 1200 MY11 2011, Руководство по обслуживанию станции, Страница: 125 / 385

Результаты поиска

Содержание Stelvio 1200 MY11 2011

Отзывы: