LG ARUM072BTE5 Скачать руководство пользователя страница 72

Страница: 72 / 184

MUL

TI V 5 Outdoor Unit Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

Header Kits

Install Correctly

• Y-branches can be installed upstream between the Header and the outdoor unit, but a Y-branch cannot be installed between a header and

an indoor unit.

• To avoid the potential of uneven refrigerant distribution through a header fitting, minimize the difference in equivalent pipe length between the

header fitting and each connected indoor unit.

INSTALLING FOR HEAT RECOVERY

OPERATION

No Substitutions on Piping Components

Only LG supplied Y-branch and Header fittings can be used to join one pipe segment to two or more segments.

Third-party

or field-fabricated components such as tee’s, Y-fittings, couplings, headers, or other branch fittings are not permitted. The

only field-provided fittings allowed in a Multi V piping system are 45° and 90° long radius elbows and full port ball valves (if

applicable).

Header Kits

LG Header kits are highly engineered devices designed to evenly

divide the flow of refrigerant, and are used to join one pipe segment

to two or more segments. Header kits are intended for use where

multiple indoor units are in the same vicinity and it would be better

to “home-run” the run-out pipes back to a centralized location. If

connecting multiple indoor units that are far apart, Y-branches may

be more economical.

LG Header Kits Consist of:

• Two headers (one liquid line, one vapor line).
• Reducer fittings as applicable.
• Molded clam-shell type peel and stick insulation covers—one for

the liquid line and one for the vapor line.

Headers must be installed with the main pipe level in the horizontal

plane. Distribution ports must be either level in the horizonal plane

or within ±3° of plumb in the vertical plane.

When connecting indoor units to a Header, always connect the unit

with the largest nominal capacity to the port closest to the outdoor

unit. Then install the next largest indoor unit to the next port, working

down to the smallest indoor unit.

Do not skip ports. All indoor

units connected to a single

Header fitting should be located

with an elevation difference

between indoor units that does

not exceed 49 feet.

ELEVATION VIEW

LG Supplied Insulation Jacket

LG Supplied Header

Field-Supplied Copper Piping

Field-Supplied Insulation

Field-Supplied Copper Piping

ELEVATION VIEW

Within ±3°

of plumb

Must be

Level

Must be

Level

Header Kit—Horizontal Rotation Limit (Ports Must Point to a Horizontal

Direction).

Vertical Header Insulation and Piping Detail (Ports Must Point to an

Upright Direction).

Largest Indoor Units

Smaller Indoor Units

ELEVATION VIEW

Header Inlet

Header End View

+0.0

-0.0

ELEVATION

VIEW

Incorrect Header Configuration.

Incorrect Header Configuration (Ports Pointing Downward).

Содержание ARUM072BTE5

























































































































































































Результаты поиска

Содержание ARUM072BTE5

Отзывы:

Похожие инструкции для ARUM072BTE5

Бренды по названию

Популярные бренды

LG ARUM072BTE5, Руководство по установке

Результаты поиска

Содержание ARUM072BTE5

Отзывы:

Похожие инструкции для ARUM072BTE5

Бренды по названию

Популярные бренды