manualshive.com logo in svg

LG ARUM072BTE5, Руководство по установке

Устройство LG ARUM072BTE5 - это мощный кондиционер с инверторной технологией. Для удобства установки и использования, скачайте бесплатно руководство по установке на manualshive.com. Важно иметь под рукой инструкцию перед началом установки. Наслаждайтесь комфортом с LG ARUM072BTE5!

Поделиться
Скачать
background image

18

MUL

TI V 5 Outdoor Unit Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.  

©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG” is a registered trademark of LG Corp.

Table 10: Triple Frame 460V Outdoor Units.

460V Outdoor Units

SPECIFICATIONS

Combination Unit Model Number

ARUM432DTE5

36.0 Ton

ARUM456DTE5

38.0 Ton

ARUM480DTE5

40.0 Ton

ARUM504DTE5

42.0 Ton

Individual Component Model Numbers

ARUM1

 

ARUM1

 

ARUM192DTE5

ARUM1

ARUM1

 

ARUM216DTE5

ARUM1

ARUM1

ARUM216DTE5

ARUM1

ARUM1

ARUM216DTE5

Cooling Performance

Nominal Cooling Capacity (Btu/h)

1

432,000

456,000

480,000

504,000

Rated Cooling Capacity (Btu/h)

2

412,000

434,000

458,000

480,000

Heating Performance

Nominal Heating Capacity (Btu/h)

1

486,000

513,000

540,000

567,000

Rated Heating Capacity (Btu/h)

2

460,000

488,000

513,000

539,000

Operating Range

Cooling (°F DB)

5 to 122

5 to 122

5 to 122

5 to 122

Heating (°F WB)

-13 to +61

-13 to +61

-13 to +61

-13 to +61

Synchronous — Cooling Based (°F DB)

14 to 81

14 to 81

14 to 81

14 to 81

Synchronous — Heating Based (°F WB)

14 to 61

14 to 61

14 to 61

14 to 61

Compressor

Inverter Quantity

HSS DC Scroll x 4

HSS DC Scroll x 4

HSS DC Scroll x 5

HSS DC Scroll x 5

Oil/Type

PVE / FVC68D

PVE / FVC68D

PVE / FVC68D

PVE / FVC68D

Fan (Top Discharge)

Type

Propeller (BLDC)

Propeller (BLDC)

Propeller (BLDC)

Propeller (BLDC)

Motor Output (kW) x Qty.

0.90x2 + 0.90x2 + 0.90x2 0.90x2 + 0.90x2 + 0.90x2 0.90x2 + 0.90x2 + 0.90x2 0.90x2 + 0.90x2 + 0.90x2

Motor/Drive

Brushless Digitally Controlled / Direct

Operating Range (RPM)

Cooling

0 - 1,150

0 - 1,150

0 - 1,150

0 - 1,150

Heating

80 - 1,150

80 - 1,150

80 - 1,150

80 - 1,150

Maximum Air Volume (CFM)

33,900

33,900

33,900

33,900

Unit Data

Refrigerant Type

R410A

R410A

R410A

R410A

Refrigerant Control/Location

EEV / Indoor Unit

EEV / Indoor Unit

EEV / Indoor Unit

EEV / Indoor Unit

Factory Charge lbs. of R410A

23.2 + 23.2 + 30.9

23.2 + 23.2 + 37.5

23.2 + 26.5 + 37.5

23.2 + 26.5 + 37.5

Max. No. Indoor Units/System

3

64

64

64

64

Sound Pressure dB(A)

4

66.0

66.0

67.0

67.0

Net Unit Weight (lbs.)

507 + 507 + 659

507 + 507 + 666

507 + 639 + 666

507 + 639 + 666

Shipping Weight (lbs.)

534 + 534 + 688

534 + 534 + 694

534 + 666 + 694

534 + 666 + 694

Communication Cables

5,6

2 x 18

2 x 18

2 x 18

2 x 18

Heat Exchanger

Material and Fin Coating

Copper Tube / Aluminum Fin and Black Coated Fin™ / Hydrophilic

Rows / Fins per inch

2/17 x 2 + 3/17

2 / 17 x 2 + 3 / 17

2 / 17 + 3 / 17 x 2 

2 / 17 + 3 / 17 x 2 

Piping for Heat Recovery Operation

7

Liquid Line Connection (in., OD)

1/2 & 1/2 & 5/8 Braze

1/2 & 1/2 & 5/8 Braze

1/2 & 1/2 & 5/8 Braze

1/2 & 5/8 & 5/8 Braze

Low Pressure Vapor Line Conn. (in., OD) 1-1/8 & 1-1/8 & 1-1/8 Braze 1-1/8 & 1-1/8 & 1-1/8 Braze 1-1/8 & 1-1/8 & 1-1/8 Braze 1-1/8 & 1-1/8 & 1-1/8 Braze

High Pressure Vapor Line Conn. (in., OD) 3/4 & 3/4 & 1-1/8 Braze 3/4 & 3/4 & 1-1/8 Braze 3/4 & 7/8 & 1-1/8 Braze 3/4 & 7/8 & 1-1/8 Braze

Piping for Heat Pump Operation

7

Liquid Line Connection (in., OD)

1/2 & 1/2 & 5/8 Braze

1/2 & 1/2 & 5/8 Braze

1/2 & 1/2 & 5/8 Braze

1/2 & 5/8 & 5/8 Braze

Vapor Line Connection (in., OD)

1-1/8 & 1-1/8 & 1-1/8 Braze 1-1/8 & 1-1/8 & 1-1/8 Braze 1-1/8 & 1-1/8 & 1-1/8 Braze 1-1/8 & 1-1/8 & 1-1/8 Braze

1

Nominal capacity applied with non-ducted indoor units, and is rated 0 ft. above sea level 

with 25 ft. of refrigerant line per indoor unit and a 0 ft. level difference between outdoor and 

indoor units. All capacities are net with a Combination Ratio between 95–105%. 

Nominal cooling capacity rating obtained with air entering the indoor unit at 80ºF dry bulb 

(DB) and 67ºF wet bulb (WB) and outdoor ambient conditions of 95ºF dry bulb (DB) and 

75ºF wet bulb (WB). 

Nominal heating capacity rating obtained with air entering the indoor unit at 70ºF dry bulb 

(DB) and 59ºF wet bulb (WB) and outdoor ambient conditions of 47ºF dry bulb (DB) and 

43ºF wet bulb (WB).

2

Rated capacity is certified under AHRI Standard 1230. See www.ahrinet.org for information.

3

The System Combination Ratio must be between 50–130%.

4

Sound pressure levels are tested in an anechoic chamber under ISO Standard 3745.

5

Communication cable between Master ODU to Slave ODU(s), and Master ODU to IDUs / 

HRUs to be 18 AWG, 2-conductor, twisted, stranded, shielded. Ensure the communication 

cable shield is properly grounded to the Master ODU chassis only.  Do not ground the 

ODU to IDUs / HRUs communication cable at any other point. Wiring must comply with all 

applicable local and national codes. 

6

Power wiring is field provided, solid or stranded, and must comply with the applicable 

local and national codes. See page 20 for detailed electrical data.

7

LG requires that LATS software be used on all projects to ensure correct line sizing. 

Designer must verify the shop drawing design against the as built design using LATS. 

Contractor must also use LG manufactured Y-Branch and Header Kits only.

Содержание ARUM072BTE5

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARUM072BTE5

Haier AD182AMEAA Operation & Instruction Manual preview
AD182AMEAA
Бренд: Haier Страницы: 22
Haier Group AD092XLERA Operation & Installation Manual preview
AD092XLERA
Бренд: Haier Group Страницы: 28
G21 Envi 12H Quick Start Manual preview
Envi 12H
Бренд: G21 Страницы: 4
Zibro S 3628 Product Data Sheet preview
S 3628
Бренд: Zibro Страницы: 2
Panasonic XE Series Operating Instructions Manual preview
XE Series
Бренд: Panasonic Страницы: 64
Soleus Air iCongo PSQ-08-01 Operating Instructions Manual preview
iCongo PSQ-08-01
Бренд: Soleus Air Страницы: 18
Dometic Breathe Easy Installation And Operating Manual preview
Breathe Easy
Бренд: Dometic Страницы: 136
Technibel SCD106C5TA Operating Instruction preview
SCD106C5TA
Бренд: Technibel Страницы: 45
Nortek AB 150A Installation And Operating Manual preview
AB 150A
Бренд: Nortek Страницы: 12
Roland FAVORITE ON-OFF Series Service Manual preview
FAVORITE ON-OFF Series
Бренд: Roland Страницы: 80
Schaefer Pro-Kool M-PROK142 User Manual preview
Pro-Kool M-PROK142
Бренд: Schaefer Страницы: 16
Hisense AVW-38UCSC Installation & Maintenance Manual preview
AVW-38UCSC
Бренд: Hisense Страницы: 42
Airwell AWSI-CBV005-N11 Operation & Installation Manual preview
AWSI-CBV005-N11
Бренд: Airwell Страницы: 24
Friedrich 9332279009-01 Installation Manual preview
9332279009-01
Бренд: Friedrich Страницы: 2
Bestron 8712184052547 Instruction Manual preview
8712184052547
Бренд: Bestron Страницы: 52
Friedrich P/N9359944072-01 Operating Manual preview
P/N9359944072-01
Бренд: Friedrich Страницы: 20
nilan Compact P User Manual preview
Compact P
Бренд: nilan Страницы: 48
b-mola NCCO1804 Operation Manual preview
NCCO1804
Бренд: b-mola Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды