LG ARUM072BTE5 Скачать руководство пользователя страница 126

Страница: 126 / 184

126

MUL

TI V 5 Outdoor Unit Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

Setting the Optional Modes

Night Low Sound Function (Fn3)

The Night Low Sound Function reduces the operating speed of the

outdoor unit fans (according to the input signal) when in cooling

mode. Operating at a low RPM reduces the fan sound levels of the

outdoor unit at night, which usually has a low cooling load.
On a rolling 24 hour basis, an internal timer begins counting hours

after the start time (delay set after peak cooling recorded operation),

switching to restricted fan speed duration operation, following what-

ever settings have been chosen.
For use on both heat pump and heat recovery systems.

Turn No. 5 on the master outdoor unit PCB

DIP switch bank SW01 to ON.

Select the “Func” mode by using the SW03C forward ►button and the

SW02C backward ◄ button, and then press the SW01C confirm

● button.

Select the “Fn3” function by using the SW03C forward ►button and

the SW02C backward ◄ button, and then press the SW01C

confirm ● button.

Select from “op1” through “op12” options (see table) by using the

SW03C forward ►button and the SW02C backward ◄ button,

and then press the SW01C confirm ● button.

Press the SW01D Reset Button one (1) time to reset PCB.

The Night Low Sound function is set; the selected option value is

saved in the EPROM.

Setting the Night Low Sound Function.

Table 48: Setting the Time and Related Sound Level.

Settings

Start Time

(Delay after Peak Cooling Recorded) (Hour)*

Restricted Fan Speed Duration

(Hour)

Approximate Noise Level dB(A)

6 Ton

8 to 20 Ton

op1

8.0

9.0

op2

6.5

10.5

op3

5.0

12.0

op4

8.0

9.0

op5

6.5

10.5

op6

5.0

12.0

op7

8.0

9.0

op8

6.5

10.5

op9

5.0

12.0

op10 (Default)

0.0 (Continuous Operation)

24.0

op11

0.0 (Continuous Operation)

24.0

op12

0.0 (Continuous Operation)

24.0

*The system measures ambient temperature (minimum and maximum) in “Wait Time” to help determine when the system can start operating in Night Low Sound.

PRE-COMMISSIONING

Содержание ARUM072BTE5

























































































































































































Результаты поиска

Содержание ARUM072BTE5

Отзывы:

Похожие инструкции для ARUM072BTE5

Бренды по названию

Популярные бренды

LG ARUM072BTE5, Руководство по установке

Результаты поиска

Содержание ARUM072BTE5

Отзывы:

Похожие инструкции для ARUM072BTE5

Бренды по названию

Популярные бренды