LG ARUM072BTE5 Скачать руководство пользователя страница 44

Страница: 44 / 184

MUL

TI V 5 Outdoor Unit Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

Selecting Field-Supplied Copper Piping

Always follow local codes when selecting and installing copper pipe and piping system components.

Approved piping for use with Multi V products will be marked “R410 RATED” along the length of the pipe. Piping wall thickness should meet

local code requirements and be approved for a maximum operating pressure of 551 psi. When bending piping, try to keep the number of

bends to a minimum, and use the largest radii possible to reduce the equivalent length of installed piping; also, bending radii greater than ten

(10) piping diameters can minimize pressure drop. Be sure no traps or sags are present.

For Heat Recovery Systems

LG prefers the use of ACR hard drawn copper on pipe segments located between heat recovery units and outdoor units, between heat recov-

ery units piped in series, and between heat recovery units and multiple indoor units sharing an heat recovery unit port.

For Heat Pump Systems

LG prefers the use of ACR hard drawn copper for all pipe segments in the piping system except segments located between Y-branch fittings

(or header fittings) and indoor units.

For DOAS Units

LG prefers the use of hard drawn copper in pipe segments connecting a Dedicated Outdoor Air System (DOAS) product and an outdoor unit.

Always properly support the piping as per the instructions on page 50.

SELECTING COPPER PIPING

Table 20: ACR Rated Copper Tubing Material.

Nominal Pipe

Outside

Diameter (in)

Actual Outside

Diameter (in)

Drawn Temper

Annealed Temper

Nominal Wall

Thickness (in)

Weight (lb/ft)

Cubic ft per

Linear ft

Nominal Wall

Thickness (in)

Weight (lb/ft)

Cubic ft per

Linear ft

1/4

0.250

0.030

0.081

0.00020

3/8

0.375

0.030

0.126

0.00054

0.032

0.134

0.00053

1/2

0.500

0.035

0.198

0.00101

0.032

0.182

0.00103

5/8

0.625

0.040

0.285

0.00162

0.035

0.251

0.00168

3/4

0.750

0.042

0.362

0.00242

0.042

0.362

0.00242

7/8

0.875

0.045

0.455

0.00336

0.045

0.455

0.00336

1-1/8

1.125

0.050

0.655

0.00573

0.050

0.655

0.00573

All dimensions provided are in accordance with ASTM B280 – Standard.

Design pressure = 551 psig.

The Copper Tube Handbook, 2010, Copper Development Association Inc., 260 Madison Avenue, New York, NY 10016.

Table 21: ACR Rated Piping Wall Thicknesses.

Type

Seamless Phosphorous Deoxidized

Class

UNS C12200 DHP

Straight Lengths

H58 Temper

Coils

O60 Temper

Table 22: ACR Copper Tubing Dimensions and Physical Characteristics

1-3

• Commercially available piping often contains dust and other materials. Always blow it clean with a dry nitrogen.

• Prevent dust, water or other contaminants from entering the piping during installation.

OD (in)

1/4

3/8

1/2

5/8

3/4

7/8

1-1/8

1-3/8

1-5/8

Material

Rigid or Soft ACR Rated for R410A

Rigid or Solid ACR Rated for R410A

Min. Bend Radius (in)

0.563

0.9375

1.5

2.25

3.0

3.5

4.0

4.5

Min. Wall Thickness (in)

0.03

0.04

0.050

Содержание ARUM072BTE5

























































































































































































Результаты поиска

Содержание ARUM072BTE5

Отзывы:

Похожие инструкции для ARUM072BTE5

Бренды по названию

Популярные бренды

LG ARUM072BTE5, Руководство по установке

Результаты поиска

Содержание ARUM072BTE5

Отзывы:

Похожие инструкции для ARUM072BTE5

Бренды по названию

Популярные бренды