LG ARUM072BTE5 Скачать руководство пользователя страница 168

Страница: 168 / 184

168

MUL

TI V 5 Outdoor Unit Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

Error Code

Description

Details

Heat Recovery Unit

- 5 1

C +

No.

of HR

Unit

Capacity of indoor units connected to the heat

recovery unit exceeds allowable limits.

The amount of nominal cooling capacity of indoor units con-

nected to a heat recovery unit, or a heat recovery unit port, or

capacity of grouped heat recovery unit port is excessive. After

auto-pipe detection is complete, wait 5 minutes, then verify

connected capacity. System will display error if:

• The heat recovery unit port addresses are all unique, but >54

Mbh single indoor unit connected; >54 Mbh total of multiple

indoor units connected.

• If 2 heat recovery unit port addresses are the same and the

ports are twinned; >108 Mbh total of multiple indoor units are

connected.

• If 3 heat recovery unit port addresses are the same and the

ports are all connected, or >162 Mbh total of multiple indoor

units connected.

• If the total connected indoor unit nominal capacity exceeds

192 Mbh for a single heat recovery unit.

• Error code displays on the outdoor unit SSD, the heat recov-

ery unit SSD, or in LGMV.

2 0 0

1 Auto pipe search failure.

Auto piping procedure did not complete properly.

2 0 1

C +

No.

of HR

Unit

Heat recovery unit liquid sensor error. (C = Heat

recovery unit + Heat recovery unit

number).

Disconnection or short circuit of heat recovery unit liquid pipe

sensor.

2 0 2

Heat recovery unit subcooling pipe inlet sensor

error. (C = Heat recovery unit + Heat recovery unit

number).

Disconnection or short circuit of heat recovery unit subcooling

pipe inlet sensor.

2 0 3

Heat recovery unit subcooling pipe outlet sensor

error. (C = Heat recovery unit + Heat recovery unit

number).

Disconnection or short circuit of heat recovery unit subcooling

pipe outlet sensor.

2 0 4

Communication error between outdoor unit and

heat recovery unit. (C = Heat recovery unit + Heat

recovery unit number)

Outdoor unit does not receive signal from heat recovery unit.

2 0 5

Communication error between heat recovery unit

(2A Series) and the 485 modem. The 2A Series heat

recovery unit applies only to heat recovery systems

communicating at a baud rate of 9,600 bps.
• The 485 modem is the communications style on

the bus that is 1e outdoor unit to many indoor units.

• Communication problem occurred between the heat recovery

unit PCB and the connection to the communications bus.

• Error displays if the outdoor unit signal is not received for

three (3) minutes. The error clears after the signal is received

from the modem. (2A Series Heat Recovery Units.)

2 0 6

Duplicate address error of the heat recovery unit

(2A Series).
• The 2A Series heat recovery unit applies only to

heat recovery systems communicating at a baud

rate of 9,600 bps.

• The 485 modem is the communications style on the

bus that is 1e outdoor unit to many indoor units.

• A heat recovery unit address is duplicated for 485 communi-

cation.

• There are two heat recovery units with one or more HEX

addresses that are the same.

• Adjust the hex address dial found on the heat recovery units.

Network

2 4 2

* Network error of central controller.

Inability of the central controller to receive information from the

outdoor unit.

For detailed information on how to troubleshoot each error, see the Multi V Service Manual on www.lghvac.com.

ERROR CODE TABLES

Table 81: Error Codes, continued.

Please refer to the Safety Precautions on pages 4-7 for more detail to prevent injury or death regarding the operation and service

troubleshooting of the Multi V product.

WARNING

Содержание ARUM072BTE5

























































































































































































Результаты поиска

Содержание ARUM072BTE5

Отзывы:

Похожие инструкции для ARUM072BTE5

Бренды по названию

Популярные бренды

LG ARUM072BTE5, Руководство по установке

Результаты поиска

Содержание ARUM072BTE5

Отзывы:

Похожие инструкции для ARUM072BTE5

Бренды по названию

Популярные бренды