LG ARUM072BTE5 Скачать руководство пользователя страница 165

Страница: 165 / 184

165

Error Codes

Due to our policy of continuous product innovation, some specifications may change without notification.

Error Code

Description

Details

Outdoor Unit

1 Master outdoor unit fan overcurrent error.

Outdoor unit fan current is >10A (for 208-230V units) or 5A (for

460V units).

2 Slave1 outdoor unit fan overcurrent error.

Slave1 outdoor unit fan current is >10A (for 208-230V units) or

5A (for 460V units).

3 Slave2 outdoor unit fan overcurrent error.

Slave2 outdoor unit fan current is >10A (for 208-230V units) or

5A (for 460V units).

1 Master outdoor unit fan operation failure error.

Master outdoor unit fan is experiencing first position sensor

failure.

2 Slave1 outdoor unit fan operation failure error.

Slave1 outdoor unit fan is experiencing first position sensor

failure.

3 Slave2 outdoor unit fan operation failure error.

Slave2 outdoor unit fan is experiencing first position sensor

failure.

1 Master outdoor unit main PCB onboard EPROM error. • Verify the EPROM is present and in the socket correctly.

• Check if all pins are in and are not bent.
• Check if notch in the chip lines up with the arrow on the

socket.

2 Slave1 outdoor unit main PCB onboard EPROM error.

3 Slave2 outdoor unit main PCB onboard EPROM error.

1 Master outdoor unit fan PCB EPROM error.

• Communication error between master outdoor unit fan MICOM

and EPROM.

• Verify EPROM is present and in the socket correctly.

2 Slave1 outdoor unit fan PCB EPROM error.

• Communication error between slave1 outdoor unit fan MICOM

and EPROM.

• Verify EPROM is present and in the socket correctly.

3 Slave2 outdoor unit fan PCB EPROM error.

• Communication error between slave2 outdoor unit fan MICOM

and EPROM.

• Verify EPROM is present and in the socket correctly.

1 0 4 1 Communication error between master outdoor unit and

slave outdoor units.

Master outdoor unit main PCB is not receiving signals from

slave outdoor units.

1 0 4 2 Communication error between slave1 outdoor unit and

master and slave2 outdoor units.

Slave1 outdoor unit main PCB is not receiving signals from

master and slave2 outdoor units.

1 0 4 3 Communication error between slave2 outdoor unit and

master and slave1 outdoor units.

Slave2 outdoor unit main PCB is not receiving signals from

master and slave1 outdoor units.

1 0 5 1 Master outdoor unit fan PCB communication error.

Master outdoor unit main PCB is not receiving a signal from the

fan.

1 0 5 2 Slave1 outdoor unit fan PCB communication error.

Slave1 outdoor unit main PCB is not receiving a signal from the

fan.

1 0 5 3 Slave2 outdoor unit fan PCB communication error.

Slave2 outdoor unit main PCB is not receiving a signal from the

fan.

1 0 6 1 Master outdoor unit fan IPM error.

Instant overcurrent (peak) of master outdoor unit fan IPM.

1 0 6 2 Slave1 outdoor unit fan IPM error.

Instant overcurrent (peak) of slave1 outdoor unit fan IPM.

1 0 6 3 Slave2 outdoor unit fan IPM error.

Instant overcurrent (peak) of slave2 outdoor unit fan IPM.

1 0 7 1 Master outdoor unit fan DC link low voltage error.

A capacitor that is serving the ODU fan inverter is not working

properly, or the voltage at the capacitor is out of range (low).
• Outdoor unit fan DC link voltage is <50V for a minimum of

250µs (for both 208-230V and 460V units).

• Disconnected DC link.
• Damaged electrical condenser component (serving capacitor)

on inverter driver board.

1 0 7 2 Slave1 outdoor unit fan DC link low voltage error.

1 0 7 3 Slave2 outdoor unit fan DC link low voltage error.

Table 78: Error Codes, continued.

For detailed information on how to troubleshoot each error, see the Multi V Service Manual on www.lghvac.com.

ERROR CODE TABLES

Please refer to the Safety Precautions on pages 4-7 for more detail to prevent injury or death regarding the operation and service

troubleshooting of the Multi V product.

WARNING

Содержание ARUM072BTE5

























































































































































































Результаты поиска

Содержание ARUM072BTE5

Отзывы:

Похожие инструкции для ARUM072BTE5

Бренды по названию

Популярные бренды

LG ARUM072BTE5, Руководство по установке

Результаты поиска

Содержание ARUM072BTE5

Отзывы:

Похожие инструкции для ARUM072BTE5

Бренды по названию

Популярные бренды