LG ARUM072BTE5 Скачать руководство пользователя страница 164

Страница: 164 / 184

164

MUL

TI V 5 Outdoor Unit Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

Error Code

Description

Details

Outdoor Unit

5 2 1 Communication error between master outdoor unit main

PCB and inverter PCB.

• Communication error between main PCB (CN-29) and inverter

PCB CN-MAIN (COM/RD).

• Check connections at both sockets.
• Inspect interconnecting cable for wear.

5 2 2 Communication error between slave1 outdoor unit main

PCB and inverter PCB.

5 2 3 Communication error between slave2 outdoor unit main

PCB and inverter PCB.

5 3 1 Communication error between outdoor unit main PCB

and indoor unit(s) PCB.

• Check if outdoor unit to indoor unit(s) communications cable

disconnected or shorted.

• Check A terminals are connected to indoor unit A(3) (5 on 3 x

3 cassette) terminals; B(4) (6 on 3 x 3 cassette) terminals.

5 7 1 Master outdoor unit main PCB and inverter PCB

communication error.

Master outdoor unit inverter PCB is not receiving signal from

main PCB.

5 7 2 Slave1 outdoor unit main PCB and inverter PCB

communication error.

Slave1 outdoor unit inverter PCB is not receiving signal from

main PCB.

5 7 3 Slave2 outdoor unit main PCB and inverter PCB

communication error.

Slave2 outdoor unit inverter PCB is not receiving signal from

main PCB.

6 0 1 Master outdoor unit inverter PCB EPROM error.

• Verify the EPROM is present and in the socket correctly.
• Check if all pins are in and are not bent.
• Check if notch in the chip lines up with the arrow on the

socket.

6 0 2 Slave1 outdoor unit inverter PCB EPROM error.
6 0 3 Slave2 outdoor unit inverter PCB EPROM error.

6 2 1 High temperature at the master outdoor unit inverter

heatsink.

System shut off because of high temperatures at the master

outdoor unit inverter heatsink.

6 2 2 High temperature at the slave1 outdoor unit inverter

heatsink.

System shut off because of high temperatures at the slave1

outdoor unit inverter heatsink.

6 2 3 High temperature at the slave2 outdoor unit inverter

heatsink.

System shut off because of high temperatures at the slave2

outdoor unit inverter heatsink.

6 5 1 Master outdoor unit inverter heatsink temperature

sensor error.

Master outdoor unit inverter heatsink temperature sensor dis-

connected or shorted.

6 5 2 Slave1 outdoor unit inverter heatsink temperature

sensor error.

Slave1 outdoor unit inverter heatsink temperature sensor dis-

connected or shorted.

6 5 3 Slave2 outdoor unit inverter heatsink temperature

sensor error.

Slave2 outdoor unit inverter heatsink temperature sensor dis-

connected or shorted.

6 7 1 Master outdoor unit fan has locked up.

No airflow.

6 7 2 Slave1 outdoor unit fan has locked up.

6 7 3 Slave2 outdoor unit fan has locked up

7 1 1 Master outdoor unit inverter CT sensor error.

Master outdoor unit is restricted.

7 1 2 Slave1 outdoor unit inverter CT sensor error.

Slave1 outdoor unit is restricted.

7 1 3 Slave2 outdoor unit inverter CT sensor error.

Slave2 outdoor unit is restricted.

7 5 1 Master outdoor unit fan CT sensor error.

Master outdoor unit fan current detection (CT) sensor discon-

nected or shorted.

7 5 2 Slave1 outdoor unit fan CT sensor error.

Slave1 outdoor unit fan current detection (CT) sensor discon-

nected or shorted.

7 5 3 Slave2 outdoor unit fan CT sensor error.

Slave2 outdoor unit fan current detection (CT) sensor discon-

nected or shorted.

Table 77: Error Codes, continued.

ERROR CODE TABLES

Please refer to the Safety Precautions on pages 4-7 for more detail to prevent injury or death regarding the operation and service

troubleshooting of the Multi V product.

WARNING

For detailed information on how to troubleshoot each error, see the Multi V Service Manual on www.lghvac.com.

Содержание ARUM072BTE5

























































































































































































Результаты поиска

Содержание ARUM072BTE5

Отзывы:

Похожие инструкции для ARUM072BTE5

Бренды по названию

Популярные бренды

LG ARUM072BTE5, Руководство по установке

Результаты поиска

Содержание ARUM072BTE5

Отзывы:

Похожие инструкции для ARUM072BTE5

Бренды по названию

Популярные бренды