LG ARUM072BTE5 Скачать руководство пользователя страница 128

Страница: 128 / 184

128

MUL

TI V 5 Outdoor Unit Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

Setting the Optional Modes

Snow Removal Assist / Rapid Defrost

Function (Fn6)

Snow Removal Assist

Snow removal assist function allows the outdoor unit(s) fans to

operate at regular intervals, for two (2) minutes, at specified speeds

below to remove snow.
The function will only operate when the system has not called for a

compressor start (no demand for heating or cooling) for thirty (30)

minutes, and the outdoor air temperature is <37ºF.

Rapid Defrost

Rapid defrost function puts the entire system in defrost at the same

time, and limits the amount of frost and ice allowed to build on the

coil between defrost cycles. System pressure is monitored, and

when system performance is reduced, the defrost cycle is initiated.

Snow removal assist / rapid defrost can also be used with Fn4

- Overall Defrost, and Fn22 - Overall Defrost Operating in Low

Temperatures (Heating).
Snow Removal Assist and Rapid Defrost can be used on both heat

pump and heat recovery systems.

• A trained LG service provider must set this function during system

installation.

• If the snow removal / rapid defrost mode is not used, set to OFF.

Turn No. 5 on the master outdoor unit PCB

DIP switch bank SW01 to ON.

Select the “Func” mode by using the SW03C forward ►button and the

SW02C backward ◄ button, and then press the SW01C confirm

● button.

Select the “Fn6” function by using the SW03C forward ►button and

the SW02C backward ◄ button, and then press the SW01C

confirm ● button.

Select from “oFF,” “op1” through “op3” options (see table) by using the

SW03C forward ►button and the SW02C backward ◄ button,

and then press the SW01C confirm ● button.

The Snow Removal / Rapid Defrost function is set.

PCB does not need reset.

Setting the Snow Removal / Rapid Defrost Function.

Settings

Details

Fan Speed During Snow Throw (RPM)

6 Ton

8 to 20 Ton

oFF (Default)

Mode Is Not Set

op1

Snow Removal Assist Mode

670

850

op2

Rapid Defrost Mode

op3

Snow Removal Assist Mode and Rapid Defrost Mode

670

850

Table 50: Setting the Snow Removal / Rapid Defrost Function.

PRE-COMMISSIONING

Содержание ARUM072BTE5

























































































































































































Результаты поиска

Содержание ARUM072BTE5

Отзывы:

Похожие инструкции для ARUM072BTE5

Бренды по названию

Популярные бренды

LG ARUM072BTE5, Руководство по установке

Результаты поиска

Содержание ARUM072BTE5

Отзывы:

Похожие инструкции для ARUM072BTE5

Бренды по названию

Популярные бренды