LG ARUM072BTE5 Скачать руководство пользователя страница 140

Страница: 140 / 184

140

MUL

TI V 5 Outdoor Unit Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

Valve (04)
Valve (03)
Valve (02)
Valve (01)

Indoor Unit (04)
Indoor Unit (03)
Indoor Unit (02)
Indoor Unit (01)

Central Control Addresses

Heat

Recovery

Unit

Central Control

Upload Central Control Address to the Indoor Units

For all ducted, vertical and floor standing indoor units, the central control address must be assigned using a wired zone controller. Wall-

mount, ceiling cassette, ceiling suspended, and the wall / ceiling convertible indoor units, the central control address can be assigned using a

wireless handheld controller or a wired zone controller.

Central Control Device

Maximum Indoor Unit Quantity

ACP IV

256

AC SMART IV

128

Table 65: Central Controller Indoor Unit Connection Limitations.

Controller Communications Limitations

Each type of Controller device is designed to communicate with a

limited quantity of indoor units. The quantity of indoor units that can

be connected to a single control communications cable, therefore,

will be defined by the control device on that cable with the smallest

Maximum Indoor Unit Quantity as shown in the tables at right.

Group Number

If the building operator wants to know which indoor units are on each outdoor unit, and multiple systems serve a building:

• Assign a Group Number to each system. If there are more than 16 indoor units on a system, multiple Group Numbers may be necessary.

If the building owner wants to know which indoor units are on each floor:

• Assign a different group number for each floor. If there are more than 16 indoor units on a floor, multiple Group Numbers may be

necessary.

Member Number

Can be assigned at will or for example, can follow the room layout on each floor.

For each LG Central Controller product provided on the project, devise a central control address schedule and assign a central control

address to each indoor unit(s) Hydro Kit(s), and ERV(s) units. Record this central control address for each component in the column provided

on the Pre-commissioning Device Configuration Worksheet.

Central Control and Indoor Units Connected to Heat Recovery Units

The heat recovery unit valve address and the central control address of its corresponding indoor unit should be set using the same number (in

manual addressing).

Integration Solutions

Maximum Indoor Unit Quantity

MultiSITE™ Communications

Manager

128

AC Smart BACnet

Gateway

128

ACP IV BACnet Gateway

256

ACP LonWorks

Gateway

Table 66: Integration Solutions Indoor Unit Connection Limitations.

BACnet

is a trademark of ASHRAE; LonWorks

is a trademark of Echlelon Corporation.

PRE-COMMISSIONING

Содержание ARUM072BTE5

























































































































































































Результаты поиска

Содержание ARUM072BTE5

Отзывы:

Похожие инструкции для ARUM072BTE5

Бренды по названию

Популярные бренды

LG ARUM072BTE5, Руководство по установке

Результаты поиска

Содержание ARUM072BTE5

Отзывы:

Похожие инструкции для ARUM072BTE5

Бренды по названию

Популярные бренды