LG ARUM072BTE5 Скачать руководство пользователя страница 117

Страница: 117 / 184

117

Pre-Commissioning

Due to our policy of continuous product innovation, some specifications may change without notification.

Vacuum Mode (Option)

• Outdoor unit operation stops during Vacuum Mode, so the com-

pressor cannot operate.

• Limit vacuum mode to less than 48 hours of continuous operation.

If vacuum mode is not stopped, the system will continue to operate

with all EEVs and valves open on the non-vacuum mode termi-

nated slave outdoor units. The refrigerant will flood back to the

compressors on those non-vacuum mode terminated slave outdoor

units, which will result in poor operation, equipment malfunction

and / or compressor damage.

Turn Master Outdoor Unit PCB No. 5 DIP Switch to ON.

Select the “SvC” Mode By Using the ►and◄

Buttons, then Push the ● Button.

Start the Vacuum Mode “vACC.”
• Outdoor Unit Valve is Fully Open.
• Outdoor Unit EEV is Fully Open.
• Indoor Unit(s) EEV(s) is/are Fully Open.
• Heat Recovery Unit(s) Valves and EEVs are

Fully Open.

Select the “Se3” Function By Using the ►and◄

Buttons, then Push the ● Button.

Setting Vacuum Mode

Canceling Vacuum Mode

Turn on Master Outdoor Unit.

<AND>

Push the Reset Button on the Outdoor Unit PCB. On a Multi-

Frame System, Push the Reset Button on ALL Outdoor Units.

Vacuum Mode (Option) (Se3)

The vacuum mode can be used as an option for creating vacuum in

the system when the outdoor unit is first installed, if power is avail-

able, and if the system has already been auto addressed. Vacuum

mode enables the system to fully open all valves, and can help

speed up the evacuation process.
Vacuum mode can also be used when compressor and / or outdoor

unit parts are replaced, or when an indoor unit is added or replaced.

1. Turn No. 5 on the master outdoor unit PCB DIP Switch SW01 to

ON.

Select the “SvC” mode By using the ►and◄ buttons, then push

the ● button.

Select the “Se3” function By using the ►and◄ Buttons, then

push the ● button.

4. Press the SW01D Reset Button one (1) time to reset PCB, and

start the vacuum mode “vACC”. In vacuum mode, the outdoor

unit valve is open, the outdoor unit EEV is open, and the indoor

unit(s) EEV(s) is/are open. The heat recovery unit(s) valve(s) and

EEVs are open (if system includes heat recovery units).

5. To cancel the vacuum mode, turn No. 5 on the master outdoor

unit PCB DIP Switch SW01 to OFF, and push the SW01D reset

button on the outdoor unit PCB. On a multi-frame system, push

the SW01D reset button on ALL outdoor units.

SW01C (

: Conﬁrm /

Automatic Addressing)

SW02C (

: Backward)

SW04C (X: Cancel)

No. 5 on DIP-SW01
SSD

SW01D (Reset)

SW03C (

: Forward)

OFF

1 2 3 4 5 6 7

No. 5 on DIP-SW01

Vacuum Mode Setting Locations.

PRE-COMMISSIONING

Содержание ARUM072BTE5

























































































































































































Результаты поиска

Содержание ARUM072BTE5

Отзывы:

Похожие инструкции для ARUM072BTE5

Бренды по названию

Популярные бренды

LG ARUM072BTE5, Руководство по установке

Результаты поиска

Содержание ARUM072BTE5

Отзывы:

Похожие инструкции для ARUM072BTE5

Бренды по названию

Популярные бренды