LG ARUM072BTE5 Скачать руководство пользователя страница 149

Страница: 149 / 184

149

Pre-Commissioning

Due to our policy of continuous product innovation, some specifications may change without notification.

Auto pipe detection is complete.

Are the numbers

of indoor units connected to the

outdoor unit and displayed on the

LED the same?

Reset the power of heat recovery unit PCB.

Confirm that the settings of Nos. 2, 3 of

SW02M correspond to the number of ports

used.

Select the “Id 5” “Ath” or “Atc” function using

►

and ◄, then

push the

●

button.

If outdoor temperature is >59°F, use “Ath”.

If that does not work, use “Atc.”

If outdoor temperature is <59°F, use “Atc”.

If that does not work, use “Ath.”

Select the “Id 6 StA” function using

► and

◄,

then push the

●

button.

"88" displays on the LED of the outdoor unit

main PCB.

Outdoor unit operates for five (5) to sixty

(60) minutes.

The number of indoor units detected is

displayed for thirty (30) seconds to one (1)

minute on the outdoor unit PCB after the

outdoor unit stops.

Display error on outdoor unit PCB.

Display error on heat recovery unit PCB.

Outdoor unit PCB: HR

→

HR unit

number

→

Valve number

Heat recovery unit: "200"

Check heat recovery and indoor

units.

Pipe detection error occurs after

thirty (30) seconds.

Check the pipe installation of the

outdoor, indoor, and heat recovery

units.

Auto pipe detection is incomplete.

Retry the auto pipe detection

procedure after troubleshooting.

Is the pipe setting condition

satisfied during indoor unit operation?

Confirm indoor unit address settings.

Turn No. 1 of SW02M of heat recovery unit

PCB to OFF.

Select the “Idu” mode using

► and ◄, then

push the

●

button.

YES

Turn master outdoor unit PCB No. 5 DIP

switch to ON.

Select the “Idu” mode using

► and ◄, then

push the

●

button.

Optional (based on site requirements):

If a large capacity indoor unit is installed:

Check the settings of Nos. 4, 5, 6 on

SW02M.

If zoning, confirm Nos. 7, 8 of SM02M are set

to ON, then confirm that the individual port

DIP switch is in the ON position for SW01M.

Auto Addressing for Pipe Detection Procedure Flowchart.

An operation sound may be heard when the

system changes modes from cooling to heat-

ing and vice versa. This is normal.

Addressing with Heat Recovery Units

PRE-COMMISSIONING

Содержание ARUM072BTE5

























































































































































































Результаты поиска

Содержание ARUM072BTE5

Отзывы:

Похожие инструкции для ARUM072BTE5

Бренды по названию

Популярные бренды

LG ARUM072BTE5, Руководство по установке

Результаты поиска

Содержание ARUM072BTE5

Отзывы:

Похожие инструкции для ARUM072BTE5

Бренды по названию

Популярные бренды