LG ARUM072BTE5 Скачать руководство пользователя страница 11

Страница: 11 / 184

Product Data

Due to our policy of continuous product innovation, some specifications may change without notification.

Table 3: Dual Frame 208-230V Outdoor Units.

SPECIFICATIONS

208-230V Outdoor Units

Unit Model Number

ARUM264BTE5

22.0 Ton

ARUM288BTE5

24.0 Ton

ARUM312BTE5

26.0 Ton

ARUM336BTE5

28.0 Ton

Individual Component Model Numbers

ARUM0

ARUM168BTE5

ARUM0

ARUM192BTE5

ARUM0

ARUM216BTE5

ARUM1

ARUM216BTE5

Cooling Performance

Nominal Cooling Capacity (Btu/h)

264,000

288,000

312,000

336,000

Rated Cooling Capacity (Btu/h)

252,000

276,000

298,000

320,000

Heating Performance

Nominal Heating Capacity (Btu/h)

297,000

324,000

351,000

378,000

Rated Heating Capacity (Btu/h)

283,000

309,000

333,000

359,000

Operating Range

Cooling (°F DB)

5 to 122

Heating (°F WB)

-13 to +61

Synchronous — Cooling Based (°F DB)

14 to 81

Synchronous — Heating Based (°F WB)

14 to 61

Compressor

Inverter Quantity

HSS DC Scroll x 3

Oil/Type

PVE / FVC68D

Fan (Top Discharge)

Type

Propeller (BLDC)

Motor Output (kW) x Qty.

0.90 x 2 + 0.90 x 2

Motor/Drive

Brushless Digitally Controlled / Direct

Operating Range (RPM)

Cooling

0 - 1,150

Heating

80 - 1,150

Maximum Air Volume (CFM)

22,600

Unit Data

Refrigerant Type

R410A

Refrigerant Control/Location

EEV / Indoor Unit

Factory Charge lbs. of R410A

23.2 + 26.5

23.2 + 30.9

23.2 + 37.5

Max. No. Indoor Units/System

Sound Pressure dB(A)

63.0

65.0

Net Unit Weight (lbs.)

507 + 639

507 + 659

507 + 666

Shipping Weight (lbs.)

534 + 666

534 + 688

534 + 694

Communication Cables

5,6

2 x 18

Heat Exchanger

Material and Fin Coating

Copper Tube / Aluminum Fin and Black Coated Fin™ / Hydrophilic

Rows / Fins per inch

2 / 17 + 3 / 17

Piping for Heat Recovery Operation

Liquid Line Connection (in., OD)

3/8 & 5/8 Braze

1/2 & 5/8 Braze

Low Pressure Vapor Line Connection (in., OD)

7/8 & 1-1/8 Braze

1-1/8 & 1-1/8 Braze

High Pressure Vapor Line Connection (in., OD)

3/4 & 7/8 Braze

3/4 & 1-1/8 Braze

Piping for Heat Pump Operation

Liquid Line Connection (in., OD)

3/8 & 5/8 Braze

1/2 & 5/8 Braze

Vapor Line Connection (in., OD)

7/8 & 1-1/8 Braze

1-1/8 & 1-1/8 Braze

Nominal capacity applied with non-ducted indoor units, and is rated 0 ft. above sea level

with 25 ft. of refrigerant line per indoor unit and a 0 ft. level difference between outdoor and

indoor units. All capacities are net with a Combination Ratio between 95–105%.

Nominal cooling capacity rating obtained with air entering the indoor unit at 80ºF dry bulb

(DB) and 67ºF wet bulb (WB) and outdoor ambient conditions of 95ºF dry bulb (DB) and

75ºF wet bulb (WB).

Nominal heating capacity rating obtained with air entering the indoor unit at 70ºF dry bulb

(DB) and 59ºF wet bulb (WB) and outdoor ambient conditions of 47ºF dry bulb (DB) and

43ºF wet bulb (WB).

Rated capacity is certified under AHRI Standard 1230. See www.ahrinet.org for information.

The System Combination Ratio must be between 50–130%.

Sound pressure levels are tested in an anechoic chamber under ISO Standard 3745.

Communication cable between Master ODU to Slave ODU(s), and Master ODU to IDUs /

HRUs to be 18 AWG, 2-conductor, twisted, stranded, shielded. Ensure the communication

cable shield is properly grounded to the Master ODU chassis only. Do not ground the

ODU to IDUs / HRUs communication cable at any other point. Wiring must comply with all

applicable local and national codes.

Power wiring is field provided, solid or stranded, and must comply with the applicable

local and national codes. See page 19 for detailed electrical data.

LG requires that LATS software be used on all projects to ensure correct line sizing.

Designer must verify the shop drawing design against the as built design using LATS.

Contractor must also use LG manufactured Y-Branch and Header Kits only.

Содержание ARUM072BTE5

























































































































































































Результаты поиска

Содержание ARUM072BTE5

Отзывы:

Похожие инструкции для ARUM072BTE5

Бренды по названию

Популярные бренды

LG ARUM072BTE5, Руководство по установке

Результаты поиска

Содержание ARUM072BTE5

Отзывы:

Похожие инструкции для ARUM072BTE5

Бренды по названию

Популярные бренды