manualshive.com logo in svg

LG ARUM072BTE5, Руководство по установке

Устройство LG ARUM072BTE5 - это мощный кондиционер с инверторной технологией. Для удобства установки и использования, скачайте бесплатно руководство по установке на manualshive.com. Важно иметь под рукой инструкцию перед началом установки. Наслаждайтесь комфортом с LG ARUM072BTE5!

Поделиться
Скачать
background image

162

MUL

TI V 5 Outdoor Unit Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.  

©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG” is a registered trademark of LG Corp.

Table 75: Error Codes, continued.

For detailed information on how to troubleshoot each error, see the Multi V Service Manual on www.lghvac.com.

ERROR CODE TABLES

Please refer to the Safety Precautions on pages 4-7 for more detail to prevent injury or death regarding the operation and service 

troubleshooting of the Multi V product.

WARNING

Error Code

Description

Details

Outdoor Unit

3 2 1 Excessive increase in master outdoor unit inverter com-

pressor1 gas discharge temperature.

• System shutdown happens when discharge pipe temperature 

rises >115°C (239°F) for 10 seconds, or compressor dome 

temperature equals 105°C (221°F) for 10 seconds.

• Check the inverter compressor discharge pipe temperature 

sensor.

• Check for low refrigerant / leaks.

• Check for a defective EEV. 

• Check for a defective liquid spray valve.

3 2 2 Excessive increase in slave1 outdoor unit inverter com-

pressor1 gas discharge temperature.

3 2 3 Excessive increase in slave2 outdoor unit inverter com-

pressor1 gas discharge temperature.

3 3 1 Excessive increase in master outdoor unit inverter com-

pressor2 gas discharge temperature.

3 3 2 Excessive increase in slave1 outdoor unit inverter com-

pressor2 gas discharge temperature.

3 3 3 Excessive increase in slave2 outdoor unit inverter com-

pressor2 gas discharge temperature.

3 4 1 Master outdoor unit compressor high pressure safety 

tripped. 

• 

Shutdown due to one (1) compressor operating at ≥30Hz, or if 

high pressure is >4,000 kPa (580 psi) for ten (10) seconds.

• Check the high pressure sensor, indoor unit or outdoor unit 

fan(s), refrigerant, EEV, service valve (may be clogged); check 

for defective outdoor unit PCB, indoor unit pipe temperature 

sensor, or hot gas valve. Also, outdoor unit may not have 

enough clearance (cooling operation), or indoor unit filter may 

be clogged (heating operation).

3 4 2 Slave1 outdoor unit compressor high pressure safety 

tripped. 

3 4 3 Slave2 outdoor unit compressor high pressure safety 

tripped. 

3 5 1 Master outdoor unit low side pressure below allowable 

limits. 

• System will shut down when an abnormal low pressure condi-

tion occurs.

• Shut down occurs when the sum of all compressors inverter 

frequency <30Hz = low <110 kPa for 1 minute.

• When operating in cooling mode: Low side pressure <400 

kPa for 1 minute; High side pressure is <2,200 kPa. Check for 

refrigerant leaks (low refrigerant charge), or a defective indoor 

unit EEV. 

• When operating in heating mode: Low side pressure <230 

kPa for 1 minute; High side pressure is <1,800 kPa. Check 

for refrigerant leaks (low refrigerant charge), or a defective 

outdoor unit EEV.

3 5 2 Slave1 outdoor unit low side pressure below allowable 

limits. 

3 5 3 Slave1 outdoor unit low side pressure below allowable 

limits. 

3 6 1 Master outdoor unit inverter 1 or inverter 2 low compres-

sion ratio.

• Outdoor unit is experiencing a problem developing compressor 

lift. Error is calling out low compression ratio. System will shut 

down and display error code “CH36*”.

• During ongoing operation, if the compression ratio is <1.6 for 

2 to 5 minutes following a change in position of the reversing 

valve (either direction). If compression ratio is <1.6, delay 5 

minutes for condition to correct itself before raising the error.

• During low ambient cooling operation following an initial 

compressor start, if compression ratio is <1.1 for 2 minutes, if 

compression ratio is <1.3 for 3 minutes.

3 6 2 Slave1 outdoor unit inverter 1 or inverter 2 low compres-

sion ratio.

3 6 3 Slave2 outdoor unit  inverter 1 or inverter 2 low com-

pression ratio.

4 0 1 Master outdoor unit inverter compressor current trans-

ducer (CT) sensor error.

Master outdoor unit inverter compressor current transducer (CT) 

detection sensor disconnected or shorted. 

4 0 2 Slave1 outdoor unit inverter compressor current trans-

ducer (CT) sensor error.

Slave1 outdoor unit inverter compressor current transducer (CT) 

detection sensor disconnected or shorted. 

4 0 3 Slave2 outdoor unit inverter compressor current trans-

ducer (CT) sensor error.

Slave2 outdoor unit inverter compressor current transducer (CT) 

detection sensor disconnected or shorted. 

4 1 1 Master outdoor unit inverter compressor1 discharge 

pipe temperature sensor error.

• Check the connection on the outdoor unit PCB.

• Thermistor disconnected or shorted.

4 1 2 Slave1 outdoor unit inverter compressor1 discharge  

pipe temperature sensor error.

4 1 3 Slave2 outdoor unit inverter compressor1 discharge  

pipe temperature sensor error.

Содержание ARUM072BTE5

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARUM072BTE5

Zibro S1126 Operating Manual preview
S1126
Бренд: Zibro Страницы: 82
Zamil CX SERIES Installation, Operation & Maintenance Manual preview
CX SERIES
Бренд: Zamil Страницы: 20
GE AEL14AV Owner'S Manual And Installation Instructions preview
AEL14AV
Бренд: GE Страницы: 36
AERMEC FCX Series Directions For Use Manual preview
FCX Series
Бренд: AERMEC Страницы: 12
Dometic GROUP WAECO VAS 581 001 Operating Manual preview
WAECO VAS 581 001
Бренд: Dometic GROUP Страницы: 328
Momax AP7S Instruction Manual preview
AP7S
Бренд: Momax Страницы: 41
Daikin 2MXS40H3V1B2 Installation Manual preview
2MXS40H3V1B2
Бренд: Daikin Страницы: 20
Maytag P4SA Series Technical Specifications preview
P4SA Series
Бренд: Maytag Страницы: 8
Gree GWH09MA-A3DNA3A Installation, Service & Troubleshooting preview
GWH09MA-A3DNA3A
Бренд: Gree Страницы: 210
Hamilton Beach 840144101 Use & Care Manual preview
840144101
Бренд: Hamilton Beach Страницы: 28
Koldfront PAC705 Owner'S Manual preview
PAC705
Бренд: Koldfront Страницы: 23
Friedrich ZoneAire Compact P08SA Owner'S Manual preview
ZoneAire Compact P08SA
Бренд: Friedrich Страницы: 32
McQuay M5CCY28CR Technical Manual preview
M5CCY28CR
Бренд: McQuay Страницы: 65
Haier HSU-10HM03-R2 Operation Manual preview
HSU-10HM03-R2
Бренд: Haier Страницы: 30
Haier AS142AHAIA Operation Manual preview
AS142AHAIA
Бренд: Haier Страницы: 29
York ZKT06 Installation Manual preview
ZKT06
Бренд: York Страницы: 72
York Sunline ZE Series Installation Manual preview
Sunline ZE Series
Бренд: York Страницы: 77
York ZV-06 Installation Manual preview
ZV-06
Бренд: York Страницы: 87

Бренды по названию

Популярные бренды

Загрузить еще бренды