Kongsberg cJoy OT Скачать руководство пользователя страница 189

Страница: 189 / 208

Message explanations

A-68

385585/C

actions:

Rudder [#] input error

See “Thruster/rudder [#] input error”.

Rudder [#] not zero

Description:

The rudder angle reading shows that the rudder is not in the neutral position. This

may be due to the rudder being out of position or the rudder pumps not started.

Additional

information:

Rudder limit.

Possible

consequences:

Full station-keeping is not guaranteed. A position and/or heading alarm may

occur.

Corrective

actions:

Check the rudder position and the rudder pumps. Set the rudder in the neutral

position.

Rudder [#] prediction error

See “Thruster/rudder [#] prediction error”.

Rudder [#] triangle pot error

See “Thruster/rudder [#] triangle pot error”.

Rudder in azimuth limits

See “Thruster/rudder in azimuth limits”.

Save PS error (see message)

Description:

This message shall not occur during normal operation, but is intended to be an aid

for the software engineer during configuration/commissioning.

Possible

consequences:

The system might not function properly.

Corrective

actions:

•

Check configuration.

•

Should this message occur during normal operation, contact Kongsberg

Maritime Service.

SBC Fan stopped

Description:

The fan on the PS (Process Station) is not running.

Содержание cJoy OT

















































































































































































































Результаты поиска

Содержание cJoy OT

Отзывы:

Похожие инструкции для cJoy OT

Бренды по названию

Популярные бренды

Kongsberg cJoy OT, Руководство оператора

Результаты поиска

Содержание cJoy OT

Отзывы:

Похожие инструкции для cJoy OT

Бренды по названию

Популярные бренды