Kongsberg cJoy OT Скачать руководство пользователя страница 61

Страница: 61 / 208

User interface

Started as Flash System Status

Shows if the controller PS has its flash PROM configured.

•

Green

— Flash PROM configured

•

Grey

— Flash PROM not configured

Mode switch Normal Status

Shows if the hex-switch on the controller PS that decides the start-up mode is in
the correct position, i.e. zero.

•

— Switch set to zero

•

Red

— Switch not set to zero

File Version Match Status

Shows if the file version of the software stored on the hard disk of the operator
terminal is the same as that stored in the flash PROM of the controller PS.

•

Green

— File versions the same

•

Red

— File versions different (mismatch)

System Information view

The System Information view shows the software configuration of the operator terminal.

The displayed information can be useful for you to have available when contacting
Kongsberg Maritime for help in case of problems with the system.

385585/C

Содержание cJoy OT

















































































































































































































Результаты поиска

Содержание cJoy OT

Отзывы:

Бренды по названию

Популярные бренды

Kongsberg cJoy OT, Руководство оператора

Результаты поиска

Содержание cJoy OT

Отзывы:

Бренды по названию

Популярные бренды