manualshive.com logo in svg

Kongsberg cJoy OT, Руководство оператора

Поделиться
Скачать
Kongsberg cJoy OT Скачать руководство пользователя страница 97

Operating procedures

This minimum RPM is a limit which defines the lowest RPM that the thruster propeller
will be allowed to rotate in either of these two modes. For example, if the minimum RPM
is set to 60% then the range for the thruster propeller RPM will be set to 60 to 100%, i.e.
the thruster propeller will not be allowed to rotate at less than 60% of its maximum RPM.

To set the minimum RPM, proceed as follows:

1

Display the Combinator Control input dialog.

2

Move the focus to the

MIN RPM

field for the thruster and change the value to the

required percentage.

3

Press the

Enter

button.

• The minimum RPM percentage is set to the value selected.

4

Close the Combinator Control input dialog.

Selecting the combinator mode

By combinator control we mean that the system controls both pitch and RPM, and that
pitch and RPM can be controlled separately.

The available combinator modes are:

•

Sequential

The RPM is kept fixed at the

MIN RPM

limit for low force demands. It will only

increase if the force demand is higher than what can be dealt with by varying the
pitch. The pitch setpoint will always be +100% or -100% when the RPM setpoint is
higher than the

MIN RPM

limit.

•

Stepwise

The RPM will be stepped up (or down) if the filtered pitch setpoint is higher (or
lower) than a pre-defined limit. It will never be stepped below the

MIN RPM

limit.

This mode is designed with long term station-keeping in mind. In this mode the
thrusters will step the RPM automatically in varying weather conditions in order to
force the pitch setpoint into a desired working interval.

•

Full

The pitch and the RPM follows a pre-defined trace (combinator curve) with regards to
the force demand.

The

Full Combinator Mode

is similar to the way in which pitch and RPM are

controlled in combinator mode when the thruster is under manual lever control.

To select the combinator mode for a thruster, proceed as follows:

1

Display the Combinator Control input dialog.

2

Move the focus to the

Combinator Mode

field for the thruster and select the required

option.

3

Press the

Enter

button.

• The combinator mode is changed to the selected option.

4

Close the Combinator Control input dialog.

385585/C

97

Содержание cJoy OT

















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды