Kongsberg cJoy OT Скачать руководство пользователя страница 200

Страница: 200 / 208

Message explanations

385585/C

A-79

Possible

consequences:

Thruster malfunction.

Corrective

actions:

Check the SVC (Kongsberg Vessel Control) Operator Station for details.

Thruster/rudder [#] triangle pot error

Description:

This message is reported because the input from the triangular "sine-cosine" pot.

meter indicates an error.
The reason for this is failure in the thruster feedback equipment or the input

interface.

Possible

consequences:

If the feedback loop is faulty the performance will be nearly unaffected. If the

control loop is faulty unexpected movements may be the result. The system may

use estimated feedback instead of measured feedback depending on configuration.

Corrective

actions:

If control seems to be degraded the thruster should be switched off. Check the

input interface and the thruster feedback equipment.

Thruster/rudder in azimuth limits

Description:

This message is reported if the azimuth or rudder angle is limited in Autopilot and

other high speed modes.
The method of detection is comparing the setpoint with the operator-specified

maximum Turn-angle for Steering Rudders/Azimuth Thrusters.
The reason for this fault may be that a low Surge demand results in a low

available moment.

Additional

information:

Steering group name, (if two or more steering groups exist).

Possible

consequences:

Degraded performance.

Corrective

actions:

Increase the Surge demand. Check the actual heading and heading setpoint, and

check the operator-specified maximum Turn-angle for Steering Rudders/Azimuth

Thrusters.
Use another operational mode e.g. Joystick - Increase Surge demand or increase

the maximum Turn-angle for Steering Rudders/Azimuth Thrusters.

Thrusters not ready

Description:

No thrusters/propellers ready for DP.
The reason for this fault may be that no thrusters or propellers are running. If the

vessel has a switch or button to select between manual and DP thruster control,

this switch/button may be set to manual. The ready state from thruster or

propeller system is not active. There may be errors in thruster or propeller

electronic, digital input interface or cabling.
The method of detection is digital input (stand-alone systems).

Possible

consequences:

Cannot perform any DP function.

Содержание cJoy OT

















































































































































































































Результаты поиска

Содержание cJoy OT

Отзывы:

Похожие инструкции для cJoy OT

Бренды по названию

Популярные бренды

Kongsberg cJoy OT, Руководство оператора

Результаты поиска

Содержание cJoy OT

Отзывы:

Похожие инструкции для cJoy OT

Бренды по названию

Популярные бренды