Kongsberg cJoy OT Скачать руководство пользователя страница 135

Страница: 135 / 208

Message explanations

A-14

385585/C

Draught limit reached

Description:

The used draught has reached the limits defined for maximum or minimum

draught. The draught value will now be set to either high limit or low limit,

depending on which of them has been violated.

Additional

information:

•

Draught value (meters).

•

Draught limit (meters)

Possible

consequences:

Used draugth value will now be "frozen" at high or low limit.

Corrective

actions:

Select one of the predifined draught values or manual draught.

Check failed sensor and its interface to the PS.

Draught not ready

See “Sensor [#] not ready”.

Draught input updated

Description:

This message is reported if the system has registered a change in draught

condition and extrapolated new mass-drag-gain.
The new draught is compared with the last value. If the difference exceeds a limit,

this message is given.
The new draught may be due to Operator input or analogue input.

Additional

information:

•

New draught (m).

The limit (m) in change of draught from the last time the message was reported.

Possible

consequences:

The Vessel Model is modified to the new load condition; new mass-drag-gain is

calculated.

Corrective

actions:

Note the Additional Information "New draught" and check that the DP has the

correct draught value.

Draught not enabled

See “Sensor not enabled”.

Содержание cJoy OT

















































































































































































































Результаты поиска

Содержание cJoy OT

Отзывы:

Похожие инструкции для cJoy OT

Бренды по названию

Популярные бренды

Kongsberg cJoy OT, Руководство оператора

Результаты поиска

Содержание cJoy OT

Отзывы:

Похожие инструкции для cJoy OT

Бренды по названию

Популярные бренды