KAESER M27 страница 53 Скачать руководство пользователя

Страница: 53 / 294

Fig. 7 Tool lubricator

Oil separator tank

Tool lubricator

Oil tank

Venting line

Air line with additional lubricant

Shut-off ball valve

Metering knob

Please note for air tools that should not be lubricated:

Lubrication with tool oil.

Air tools that must not be lubricated can be damaged.
➤ Blow any residual oil out of the line before connecting such an air tool.

4.6.2 Option ga, gb

Generator option

A generator is installed to provide a power supply to electrical consumers. The generator is driven

from the engine by a drive belt. A tensioning device automatically ensures optimum belt tension.

Version without FAD limitation

Activating the generator does not influence the volume of compressed air delivered. The compres‐

sor delivers its full capacity regardless of current being drawn from the generator.

Version with FAD limitation

When the generator is activated, the air inlet at the inlet valve is limited. The compressor delivers

less compressed air. The engine is protected from overloading. See chapter 2.7.3 for reduced

compressed air delivery. The volume of compressed air available is dependent on the generator

operating mode and the power taken.

4.6.2.1 Operating modes

The compressor works with the normal air delivery regulation and generates electrical power at the

same time.

Design and Function

4.6

Options

No.: 9_9548 05 USE

Operator Manual Screw Compressor
M27

Option ga

Option gb

Содержание M27







































































































































































































































































































Результаты поиска

Содержание M27

Отзывы:

Похожие инструкции для M27

Бренды по названию

Популярные бренды

KAESER M27, Руководство оператора

Результаты поиска

Содержание M27

Отзывы:

Похожие инструкции для M27

Бренды по названию

Популярные бренды