KAESER M27 Скачать руководство пользователя | Manualshive

Страница: 88 / 294

background image

Fig. 27 Jumper cable connection diagram

a

Assisting vehicle battery (external donor

battery)

b

Engine battery (receiving battery)

1

Positive (+) terminal starting assistance

2

Positive (+) terminal of the machine battery

3

Bare metal point on the engine block

(earth)

4

Negative (-) terminal of assisting vehicle

battery

Complying with safety warings

1.

Fault in starting aid process!

➤ Connect batteries of the same voltage only.
➤ Ensure that machine and assisting vehicle do not touch.
➤ Switch off all consumers prior to connecting and disconnecting the batteries.
➤ Only use battery jumper cables of sufficient diameter and with insulated terminal clamps.
➤ Observe the instructions provided with the battery jumper cables.
➤ Keep jumper cables away from rotating parts.
➤ Avoid short-circuits due to incorrect poling and/or bridging with tools.
➤ Do not bend over the battery when attaching jumper cables.
➤ Do not attempt to start the machine if its battery is frozen. Allow the battery to thaw first.
➤ Do not try to start the machine with a boost charger.

2. Comply with the safety instruction shown when using starting aids and starter batteries.

Preparations

1. Park the assisting vehicle in close distance to the engine, without their bodywork touching each

other.

2. Stop the engine of the assisting vehicle.
3. Open the accesses to the batteries (remove maintenance panels/bonnet and pole caps).
4. Switch off all power consumers.

Connecting the battery jumper cables

1. Connect the positive terminals

2

and

1

.

2.

Explosion hazard!

A spark may ignite an explosive gas mixture.
➤ Do not, under any circumstances, connect the negative pole of the assisting machine to

the negative pole of the battery in the machine to be started.

This can cause sparks when connecting and disconnecting.

➤ Work with caution.

3. Connect the minus pole of the assisting battery

4

to a bare metal point on the compressor en‐

gine

3

to be started as far away from the battery as possible.

7

Initial Start-up

7.4

Low-temperature operation (winter)

78

Operator Manual Screw Compressor
M27

No.: 9_9548 05 USE

«
...
86
87
88
89
90
...
»

Содержание M27







































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M27

BRONCO 2 OIL FREE

Бренд: Clarke Страницы: 8

Бренд: Ingersoll-Rand Страницы: 72

YCAS0250-0440 60 HZ

Бренд: York Страницы: 9

BrakeMaster 8310

Бренд: Roadmaster Страницы: 2

Бренд: Roadmaster Страницы: 2

Бренд: Nuvair Страницы: 40

Бренд: VIAIR Страницы: 8

Бренд: Ryobi Страницы: 18

Бренд: Ryobi Страницы: 16

Бренд: Ryobi Страницы: 19

Бренд: MGF Страницы: 34

ENTERPRISE E140

Бренд: Mouvex Страницы: 2

Бренд: Mouvex Страницы: 12

Бренд: California Air Tools Страницы: 16

Бренд: California Air Tools Страницы: 17

Бренд: California Air Tools Страницы: 17

MLZ Evolution A

Бренд: Danfoss Страницы: 48

Бренд: Ferm Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды