KAESER M27 Скачать руководство пользователя | Manualshive

Страница: 31 / 294

background image

3 Safety and Responsibility

3.1 Basic instructions

The machine is manufactured to the latest engineering standards and acknowledged safety regula‐

tions. Nevertheless, dangers can arise through its operation:
■ danger to life and limb of the operator or third parties,
■ Impairments to the machine and other material assets.

Disregard of warning or safety instructions can cause serious injuries!

➤ Use this machine only if it is in a technically perfect condition and only for the purpose for

which it is intended; observe all safety measures and the instructions in the service manual!

➤ Immediately rectify (have rectified) any faults that could be detrimental to safety!

3.2 Specified use

The machine is intended solely for generating compressed air for industrial use. Any other use is

considered incorrect. The manufacturer is not liable for any damages that may result from incorrect

use. The user alone is liable for any risks incurred.
➤ Keep to the specifications listed in this service manual.
➤ Operate the machine only within its performance limits and under the permitted ambient condi‐

tions.

➤ Do not use compressed air for breathing purposes unless it is specifically treated.
➤ Do not use compressed air for any application that will bring it into direct contact with food

products unless it is specifically treated.

3.3 Incorrect Use

Improper usage can cause damage to property and/or (severe) injuries.
➤ Only use the machine as intended.
➤ Never direct compressed air at persons or animals.
➤ Do not use untreated compressed air for breathing purposes.
➤ Do not allow the machine to take in toxic, acidic, flammable, or explosive gases or vapors.
➤ Do not operate the machine in areas in which specific requirements with regard to explosion

protection are in effect.

3.4 User's Responsibilities

3.4.1 Observe statutory and universally accepted regulations

➤ Observe relevant statutory and accepted regulations during operation, transporting and main‐

tenance of the machine.

3

Safety and Responsibility

3.1

Basic instructions

No.: 9_9548 05 USE

Operator Manual Screw Compressor
M27

21

«
...
29
30
31
32
33
...
»

Содержание M27







































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M27

Бренд: Diamond Air Страницы: 20

Бренд: DeVilbiss Страницы: 16

Бренд: Huvema Страницы: 14

Бренд: Meec tools Страницы: 36

Бренд: Kyocera Страницы: 132

Бренд: Hanbell Страницы: 22

Бренд: MGF Страницы: 8

Бренд: MGF Страницы: 8

Бренд: Prematic AG Страницы: 97

Бренд: Danfoss Страницы: 2

Бренд: Bambi Страницы: 12

Бренд: Bambi Страницы: 12

Бренд: Sagola Страницы: 24

Бренд: Atlas Copco Страницы: 94

Бренд: Campbell Hausfeld Страницы: 2

Бренд: Truper Страницы: 16

Бренд: Truper Страницы: 20

Бренд: Truper Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды