KAESER M27 Скачать руководство пользователя | Manualshive

Страница: 134 / 294

background image

10.3.6 Drive belt maintenance

The life of the drive belts is influenced by belt tension.

■ Slack belts can slip and become damaged and may result in engine overheating.
■ Over-tight belts stretch and wear quicker. Over-tight belts also place unnecessary stress on

bearings and shorten their life.

Material V-belt tension measuring device

Spares

Precondition The machine is shut down.

The machine is fully vented, the pressure gauge reads 0 psig.
The machine is cooled down.
All compressed air consumers are disconnected and the air outlet valves are open.
Negative cable to the batteries disconnected.

Beware of rotating pulleys and moving belts.

There is danger of serious injury from pinching.
➤ Never check the drive belts unless the engine is at standstill.
➤ Never run the machine without a belt guard.

➤ Open the cover.

10.3.6.1 Visual inspection

Precondition Belt guard is removed

1. Check the belts thoroughly for cracks, fraying or stretching.

When damaged or worn: Replace the drive belt immediately.

2. Replace the belt guard.
3. Reconnect the negative battery terminal.
4. Close the cover.

10.3.6.2 Checking belt tension

Check belt tension when the belts are warm, not hot, to avoid length variations through tempera‐

ture.
The engine manufacturer recommends a tension measuring device for belts. See the engine serv‐

ice manual.
The belt tension may also be checked by hand if no tension measuring device is available.

10 Maintenance

10.3 Engine maintenance

124

Operator Manual Screw Compressor
M27

No.: 9_9548 05 USE

«
...
132
133
134
135
136
...
»

Содержание M27







































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M27

Бренд: MESTIC Страницы: 20

Бренд: Rietschle Страницы: 40

Бренд: Fender Страницы: 8

Бренд: Daewoo Страницы: 7

Бренд: California Air Tools Страницы: 16

Бренд: California Air Tools Страницы: 17

Бренд: California Air Tools Страницы: 18

Бренд: Grizzly Страницы: 16

SBBHS030020SD10

Бренд: Powerex Страницы: 12

Бренд: Clas Ohlson Страницы: 12

Бренд: Clas Ohlson Страницы: 24

Бренд: Clas Ohlson Страницы: 40

Бренд: Chicago Pneumatic Страницы: 28

Бренд: Chicago Pneumatic Страницы: 94

Бренд: Danfoss Страницы: 58

Бренд: California Air Tools Страницы: 17

Бренд: Bostitch Страницы: 53

POWERplus POWX1723

Бренд: VARO Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды