KAESER M27 Скачать руководство пользователя | Manualshive

Страница: 149 / 294

background image

7. Check the oil level after about 5 minutes.

Top off if necessary.

8. Carry out a visual check for leaks.
9. Close the canopy.

10.4.7 Compressor air filter maintenance

Compressor air filter maintenance
■ The filter element must replaced at the latest when the corresponding maintenance indicator

responds.

■ As stipulated in the maintenance table, replace the filter element after two years.

■ Using the machine without an air filter element is not permitted!
■ Do not use filter elements with damaged surface or seals.
■ The use of an unsuitable air filter can permit dirt to ingress into the pressure system and

cause premature wear and damage to the machine.

Material Spares

Cleaning cloth

Precondition The machine is shut down.

The machine is fully vented, the pressure gauge reads 0 psig.
The machine is cooled down.
All compressed air consumers are disconnected and the air outlet valves are open.

Dirty air filter element

Loss of machine performance
➤ Replace the filter element.

➤ Open the cover.

Checking contamination of the air filter

Air filter maintenance is necessary when the yellow piston inside the maintenance indicator rea‐

ches the red zone.

10 Maintenance

10.4 Compressor Maintenance

No.: 9_9548 05 USE

Operator Manual Screw Compressor
M27

139

«
...
147
148
149
150
151
...
»

Содержание M27







































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M27

Бренд: Makita Страницы: 31

Бренд: Scheppach Страницы: 136

Бренд: Scheppach Страницы: 120

Бренд: Pulsar Страницы: 16

Бренд: EUROPE PROJECTION Страницы: 20

YCAS0250-0440 60 HZ

Бренд: York Страницы: 9

Бренд: Ingersoll-Rand Страницы: 43

Бренд: EKOM Страницы: 84

Бренд: Accorroni Страницы: 44

Бренд: L&W Compressors Страницы: 140

Бренд: Power Craft Страницы: 14

Бренд: DENAIR Страницы: 48

Бренд: Atlas Copco Страницы: 64

Бренд: Atlas Copco Страницы: 76

Бренд: Atlas Copco Страницы: 94

Бренд: L&W Compressors Страницы: 188

LW 230 E II Compact

Бренд: L&W Compressors Страницы: 187

Бренд: WilTec Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды