manualshive.com logo in svg

KAESER M27, Руководство оператора

Поделиться
Скачать
KAESER M27 Скачать руководство пользователя страница 36

■ Eye protection
■ Ear protection

3.5.2.1 Transporting

The weight and size of the machine require safety measures during its transport to prevent acci‐

dents.
➤ Allow transportation only by personnel trained in safely dealing with motor vehicles and the

transporting of goods.

➤ Ensure that no persons are on the machine when transporting.

Transporting as trailer

Non-compliance with the basic rules for safe trailer operation may cause severe accidents during

machine transport.
➤ The maximum permissible load for the towing vehicle coupling and the maximum coupling load

given for the machine must not be exceeded.

➤ Avoid causing a shift in the center of gravity by an excessive or incorrectly distributed load.
➤ Do not tow in a manner that will impose excessive stress on the machine or chassis.
➤ Adjust towing speed to accommodate ground conditions. This applies particularly to unpaved

roads and when taking curves.

➤ The towbar must be parallel with the ground otherwise towing instability can develop, resulting

in damage to the machine and/or towing vehicle.

➤ Before moving the machine, make sure any security devices (e.g. anti-theft chain) are re‐

leased.

Transporting as trailer on public roads

➤ Do not tow machines without illumination and signaling equipment on public roads.
➤ Ensure all running gear, including chassis, wheels, brakes, signalling and lighting, is in safe

condition.

➤ The local laws and regulations regarding the use of public roads must be observed.

Transporting with a crane

Non-compliance with the safety regulations for load suspension and hoisting equipment may cause

severe accidents during lifting and moving the machine with cranes.
➤ Do not enter the danger zone while the machine is being lifted.
➤ Never lift and move the machine over people or occupied buildings.
➤ Avoid extreme weight shifting caused by additional loads or additions (tilting).
➤ Do not exceed the lifting capacity on the machine's lifting point (lifting eye).
➤ Only the designated lifting point should be used to attach lifting gear and under no circumstan‐

ces are handles, towbar or other components to be used.

➤ Use only hooks and shackles that comply with local safety regulations.
➤ Do not attach cables, chains or ropes directly to the machine's lifting eye.
➤ Do not manipulate the crane suspension system, in particular the holding points of the crane

lifting eye.

➤ If screwed crane fixings had to be removed, please use only new self-locking nuts when instal‐

ling.

3

Safety and Responsibility

3.5

Dangers

26

Operator Manual    Screw Compressor   
M27  

No.: 9_9548 05  USE

Содержание M27







































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды