KAESER M27 Скачать руководство пользователя

Страница: 108 / 294

Possible cause

Remedy

Where can I get help?
Specialized

workshop

KAESER

Service

The engine runs at maximum

speed (LOAD).

See chapter 9.2.

Engine air filter and/or compres‐

sor air filter clogged.

Clean or change, see chap‐

ters 10.3.2 and 10.4.7.

–

Oil separator cartridge heavily

clogged.

Change, see chapter 10.4.6.

–

Tab. 72 Alarm: Working pressure too low

9.3.3 Safety relief valve blowing off

Possible cause

Remedy

Where can I get help?
Specialized

workshop

KAESER

Service

Oil separator cartridge heavily

clogged.

Change, see chapter 10.4.6.

–

Inlet valve not closing.

Check the controller, the control

air line and the inlet valve and

replace if necessary.

–

Pressure relief valve maladjus‐

ted and/or leaking.

Adjust or have replaced if nec‐

essary.

–

Tab. 73 Alarm: Safety relief valve blowing off

9.3.4 Machine overheating

Possible cause

Remedy

Where can I get help?
Specialized

workshop

KAESER

Service

Defective cooling fan.

Have the blades or the complete

fan wheel replaced.

–

Oil cooler clogged.

Clean surface, see chap‐

ter 10.5.

–

Defective working element in the

combination valve.

Have repaired or replaced if

necessary.

–

Working pressure too high (pro‐

portional controller maladjus‐

ted).

Reset to the permissible value

or have replaced.

–

Oil separator cartridge heavily

clogged.

Measure the pressure differen‐

tial and change the cartridge if

greater than 14.5 psig. Change,

see chapter 10.4.6.

–

Compressor oil filter clogged.

Change, see chapter 10.4.4.

–

Compressor cooling oil level too

low.

Topping up, see chapter 10.4.2.

–

Fault Recognition and Rectification

9.3

Compressor faults and alarms

Operator Manual Screw Compressor
M27

No.: 9_9548 05 USE

Содержание M27







































































































































































































































































































Результаты поиска

Содержание M27

Отзывы:

Похожие инструкции для M27

Бренды по названию

Популярные бренды

KAESER M27, Руководство оператора

Результаты поиска

Содержание M27

Отзывы:

Похожие инструкции для M27

Бренды по названию

Популярные бренды