KAESER M27 Скачать руководство пользователя | Manualshive

Страница: 11 / 294

background image

1 Regarding this Document

1.1 Using this document

The operating manual is a component of the product. It describes the machine as it was at the time

of first delivery after manufacture.
➤ Keep the operating manual in a safe place throughout the life of the machine.
➤ Supply any successive owner or user with this operating manual.
➤ Please insert any amendment or revision of the operating manual sent to you.
➤ Enter details from the machine nameplate and individual items of equipment in the table in

1.2 Further Documents

Further documents included with this operating manual are:
■ Certificate of acceptance / operating instructions for the pressure vessel
■ Manufacturer’s declaration / declaration of conformity in accordance with applicable directives
■ Engine documentation (compressors driven by internal combustion engine)

Missing documents can be requested from KAESER.
➤ Make sure all documents are complete and observe the instructions contained in them.
➤ Make sure you provide the data from the nameplate when ordering documents.

1.3 Copyright

This operator manual is copyright protected. Queries regarding use or duplication of the documen‐

tation should be referred to KAESER. Correct use of information will be fully supported.

1.4 Symbols and labels

➤ Please note the symbols and labels used in this document.

1.4.1 Warnings

Warning notices indicate dangers that may result in injury when disregarded.

Warning notices indicate three levels of danger identified by the corresponding signal word:

Signal term Meaning

Consequences of ignoring the warning

DANGER

Warns of an imminent danger

Will result in death or severe injury

WARNING Warns of a potentially imminent danger

May result in death or severe injury

CAUTION Warns of a potentially dangerous situation May result in a moderate physical injury

Tab. 1 Danger levels and their definitions (personal injury)

Warning notices preceding a chapter apply to the entire chapter, including all sub-sections.
For example,

1

Regarding this Document

1.1

Using this document

No.: 9_9548 05 USE

Operator Manual Screw Compressor
M27

1

«
...
9
10
11
12
13
...
»

Содержание M27







































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M27

Бренд: Quincy Страницы: 12

Бренд: Tamiya Страницы: 8

DC850R Pro Series

Бренд: paasche Страницы: 2

Бренд: Ingersoll-Rand Страницы: 71

Бренд: Meec tools Страницы: 36

Бренд: EKOM Страницы: 78

Бренд: EKOM Страницы: 104

Бренд: EKOM Страницы: 108

Бренд: EKOM Страницы: 136

Бренд: Mannesmann Страницы: 33

Бренд: Gude Страницы: 64

Бренд: LA Audio Страницы: 2

Бренд: Atmos Страницы: 55

Бренд: MIA Страницы: 10

Бренд: Sparmax Страницы: 4

Бренд: California Air Tools Страницы: 16

Бренд: California Air Tools Страницы: 17

Бренд: California Air Tools Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды