manualshive.com logo in svg

KAESER M27, Руководство оператора

Поделиться
Скачать
KAESER M27 Скачать руководство пользователя страница 152

Damage to the machine can be caused by water or steam jets.

Direct water or steam jets can damage or destroy electrical components and indicating in‐

struments.
➤ Cover up electrical components such as the control cabinet, alternator, starter and in‐

struments.

➤ Do not direct water or steam jets at sensitive components such as alternator, starter or

indicating instruments.

➤ Deploy the extension pole of the pressure washer at a distance of at least 50 cm and an

approximately 90° angle to the cooler/radiator surface.

➤ Raise the cover.

10.5.1  Cleaning the compressor cooler and engine radiator

The compressor oil cooler and engine coolant radiator are combined in a single cooler block. In

order to clean both coolers, you must open the cover to its maximum opening angle. For this pur‐

pose, you must remove the two gas struts at the cover. Use a screwdriver to slightly lift the clip of

the ball cup and simultaneously draw the ball cup from the ball head. Keep the clip on the ball cup.

Connection elements, po‐

sitions

Ball head

Ball cup with clip

Ball cup

Cover interior

X

–

–

Gas strut cylinder

–

X

–

Body interior

X

Gas strut piston

–

–

X

Tab. 88 Connecting elements

Unhinge the gas struts of the cover

Precondition Cover is opened.

Use a suitable object or a second person to support the cover.

1. Push a suitable screwdriver below the clip of the ball cup of the gas strut cylinder.
2. Slightly angle and hold the screwdriver.

The clip opens.

3. Pull the ball cup off the ball head.
4. Proceed in the same manner with the second gas strut.

Both gas struts are unhinged.

5. Fully open the cover.

Result The coolers are now accessible from the outside.

Cooler cleaning

1. Seal off the air intakes of the engine and compressor air filters before starting cleaning.
2. Clean the cooling fins with compressed air, water or steam jet in the opposite direction to the

cooling air flow (from inside to outside).

3. Remove the protective coverings from the air filters.

10 Maintenance

10.5 Cleaning the cooler

142

Operator Manual    Screw Compressor   
M27  

No.: 9_9548 05  USE

Содержание M27







































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды