KAESER M27 страница 229 Скачать руководство пользователя | Manualshive

Страница: 229 / 294

background image

12.2.2.1 Preparing for transport

Stowing payload

Do not exceed the permissible loading (overall mass, coupling load, axle load).

Observe national traffic laws. If additional loading is not permitted, the load must be transported in

the towing vehicle.
1. Check that loading the machine with tools or accessories during transport is permissible.
2. Place additional loads only in the spaces provided (if available) and secure carefully.

Additional precautions for a very dirty machine

The machine can become very dirty after prolonged use on a construction site. A machine in such

condition is not suitable for towing on public roads.
1. Clean the machine, in particular around the chassis and the lighting and signalling equipment.
2. Check the function of wheels, brakes, lights and signalling equipment.

If defects are found: Correct any defects before towing.

Additional precautions for conditions of snow and ice

Considerable snow or ice may build up on the machine under low temperature conditions.
1.

Accident hazard due to snow or ice falling off the machine.

Snow or ice falling from the towed machine can endanger following vehicles.

Problems with driving dynamics and damage to the machine could occur.

The maximum permissible axle load could be exceeded.
➤ Do not transport the machine if it is covered by snow or ice.

2. Remove any snow or ice before towing.

Perform the following tasks prior to transporting the machine

1. Make sure the towing hitch is compatible with the ball or eye coupling on the towed machine.
2. Check that the machine is shut down and secured against accidental restarting.
3. Detach all connecting lines and hoses.
4. Make sure there are no unsecured tools lying on or in the machine.
5. Close and lock the canopy.

Adjust the towbar to suit the height of the towing vehicle hitch

When the machine is coupled up, the towing bar must be parallel with the ground.

Fig. 72 Transport position

12 Decommissioning, Storage and Transport

12.2 Transport

No.: 9_9548 05 USE

Operator Manual Screw Compressor
M27

219

Option rb/rm/rr, rb/rm/rs

«
...
227
228
229
230
231
...
»

Содержание M27







































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M27

PROFESSIONAL 99901

Бренд: Central Pneumatic Страницы: 8

Бренд: Würth Страницы: 268

Бренд: North Star Страницы: 35

Бренд: Atlas Copco Страницы: 110

PNS 1250 Cud S3A/T3 APP

Бренд: Atlas Copco Страницы: 114

Бренд: Champion Страницы: 40

ROTORCHAMP EWF99C-100

Бренд: Champion Страницы: 75

Бренд: Atmos Страницы: 57

Бренд: WilTec Страницы: 10

Бренд: Campbell Hausfeld Страницы: 2

Бренд: Sullivan-Palatek Страницы: 100

Бренд: Gahl Страницы: 10

Бренд: ARB Страницы: 5

EX-HG(X)44e/475-4

Бренд: GEA Bock Страницы: 56

Бренд: Zanotti Страницы: 76

Бренд: TNT Страницы: 30

Бренд: California Air Tools Страницы: 17

Бренд: RAMVAC Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды