KAESER M27 Скачать руководство пользователя

Страница: 120 / 294

Fig. 38 Checking coolant level

Water cooler

Coolant expansion tank

maximum marking (FULL)

minimum marking (LOW)

Filler port with cap

Overflow

Motor connection hose

1. Check the level of coolant in the expansion tank.

Top off when the coolant level falls below the

minimum marking

2. Close the canopy.

Determine and rectify the cause of coolant loss.

10.3.1.2 Checking the coolant

The coolant should be checked according to the maintenance schedule to ensure quality and op‐

erational life.

Coolant quality can be determined by the following parameters:
■ Visual check
■ Antifreeze concentration measurement

➤ Unscrew and remove the expansion tank filler cap

Visual check

The coolant should be checked for its color and any particles or sediments floating in it.
➤ Take a coolant sample and have analyzed.

The coolant should be changed if it is discolored or has floating particles.

Antifreeze concentration measurement

An instrument (e.g. refractometer) is used to check antifreeze concentration.

10 Maintenance

10.3 Engine maintenance

110

Operator Manual Screw Compressor
M27

No.: 9_9548 05 USE

Содержание M27







































































































































































































































































































Результаты поиска

Содержание M27

Отзывы:

Похожие инструкции для M27

Бренды по названию

Популярные бренды

KAESER M27, Руководство оператора

Результаты поиска

Содержание M27

Отзывы:

Похожие инструкции для M27

Бренды по названию

Популярные бренды