manualshive.com logo in svg

KAESER M27, Руководство оператора

Поделиться
Скачать
KAESER M27 Скачать руководство пользователя страница 122

Make sure that there is sufficient room for the coolant to expand when hot without overflow‐

ing.

Precondition The negative cable to the battery is disconnected.

1. Remove the expansion tank filler cap.
2. Mix a quantity of coolant according to the table and top up to the mark.

Top up until the coolant level is just below the 

maximum marking 

A

.

3. Screw on the filler cap.
4. Reconnect the negative battery terminal.
5. Close the canopy.
6. Start the engine and allow to IDLE for about 1 minute.
7. Stop the engine.
8. Open the canopy.
9. Check the coolant level.

Top up if the coolant level in the expansion tank has fallen.

10. Carry out a visual check for leaks.
11. Close the canopy.

10.3.1.5 Draining the coolant

Precondition The machine is cooled down.

The negative cable to the battery is disconnected.

The entire cooling agent of the motor can be drained by opening the screw plug at the water cool‐

er.

Fig. 39 Draining the coolant from the radiator

1

Water cooler

2

Drain point, water cooler

3

Gasket

4

Screw plug

1. Remove the expansion tank filler cap.
2. Position a receptacle beneath the water cooler drain point 

2

.

3. Remove the plug 

4

.

Cooling agent is drained.

10 Maintenance

10.3 Engine maintenance

112

Operator Manual    Screw Compressor   
M27  

No.: 9_9548 05  USE

Содержание M27







































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды