manualshive.com logo in svg

IOtech MultiScan 1200, Руководство пользователя

Поделиться
Скачать
IOtech MultiScan 1200 Скачать руководство пользователя страница 64

54     Chapter 7: Power & Assembly

TempScan / MultiScan User's Manual

Power-Up Activation

At initial power-up or on the 

Reset Power-On

 (

*R

) command, the TempScan/1100 or MultiScan/1200

performs automatic self-tests to ensure that it is fully functional.  The front panel LED indicators show
any errors if they occur.  Possible error conditions and their corresponding LED indicator patterns are
shown in the following table.  Any LED pattern not shown is an internal error that is not field-
serviceable; in this case, contact the factory.  If ERROR is on by itself, there is a configuration error
due to setup information in NV-RAM.  Check the error using the 

Query Error Status

 (

E?

) command.

LED Indicators

Error Condition

TALK

LISTEN

SRQ

ERROR

POWER

No Errors

(Off)

(Off)

(Off)

(Off)

ON

General Hardware Failure

ON

(Off)

ON

FLASHING

ON

Position-U22 ROM Invalid

(Off)

(Off)

(Off)

FLASHING

ON

Position-U21 ROM Checksum Error

(Off)

(Off)

ON

FLASHING

ON

Position-U22 ROM Checksum Error

(Off)

ON

(Off)

FLASHING

ON

Non-Volatile RAM Error

ON

(Off)

(Off)

FLASHING

ON

Dynamic RAM Error

ON

ON

(Off)

FLASHING

ON

Interprocessor COM Error

ON

ON

ON

FLASHING

ON

If no problems are found, the 

POWER

 LED indicator will remain on while the rest of the indicators will

go out, and the TempScan/1100 or MultiScan/1200 will begin its power-up initialization.  This self test
is performed each time the unit is powered up regardless of whether power-on was caused by the power
switch or the 

Reset Power-On

 (

*R

) command.  During initialization, the self test performs the following

steps:

1.

 

Checks for errors at power-up.

2.

 

Checks the flag in the NV-RAM to determine if it should power-up with factory default settings or
a user-defined configuration.

3.

 

Loads appropriate registers with corresponding values in NV-RAM.

4.

 

Checks a flag to see if alarms should be enabled at power-up, and if so, enables them.

5.

 

Loads channel configuration registers.

6.

 

Loads program sequencer with appropriate channel configurations.

7.

 

Resets computations processor to begin acquiring scans.

The self test takes approximately five seconds to complete, after which the TempScan/1100 or
MultiScan/1200 unit is ready for normal operation.

For more information, see section 

Power-Up Configuration

 in the chapter 

System Configuration

.

Содержание MultiScan 1200













































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды