IOtech MultiScan 1200 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 364

IOtech MultiScan 1200 Скачать руководство пользователя страница 25

TempScan / MultiScan User's Manual

Chapter 2: TempScan/1100 & MultiScan/1200 15

Data Storage & Format

Storage:

128 K reading (256 Kbyte) standard; optional 500 K reading (1 Mbyte), 2 M reading (4

Mbyte), 4 M reading (8 Mbyte).

Data Formats:

ASCII and binary; binary format returns a 16-bit compensated and linearized

temperature value (0.1°C/bit); user-programmable for hi/low byte or low/hi byte. Note that high
speed DMA transfers are binary format only.

Statistical Parameters:

High, Low, and Last available per channel.

For MultiScan/1200:

Not

available when in single-channel burst mode.

Time Stamping:

Available for each scan group and for each channel’s high, low, and last parameters.

For MultiScan/1200:

Not available when in single-channel burst mode.

Time Format:

Absolute Time/Date stamping (

hh:mm:ss.mil,MM/DD/YY

), relative Time/Date

stamping (

+hh:mm:ss.mil,DDDDDDD

) and scan interval timebase (

hh:mm:ss.t

).

For

MultiScan/1200:

Not available when in single-channel burst mode.

Alarm Stamp:

Available for each scan group.

For MultiScan/1200:

Not available when in single-

channel burst mode.

Digital Input Stamp:

Available for each scan group.

For MultiScan/1200:

Not available when in

single-channel burst mode.

IEEE 488 Interface

CAUTION

CAUTION

CAUTION

CAUTION

The IEEE 488 terminal must only be used to control a non-isolated IEEE 488
system. The common mode voltage (cable shell to earth) must be zero.

Interface Use:

Digital communication (as opposed to analog) for IEEE 488 compliant computer

platforms, as well as IEEE 488 compliant

platform-independent

configurations. Messages sent 1

byte (8 bits) at a time. Supports data rates up to 1 Mbyte/sec. Up to 15 devices can be connected
to one bus. Total bus length up to 20 meters. Allowable cable distance between devices is up to 2
meters. Message transactions are hardware handshaked.

Installation Category:

For CE:

Category 1.

Implementation:

SH1, AH1, T6, TE4, L4, LE4, SR1, PP0, RL0, DC1, DT1, C0, E1.

Programmable Parameters:

Alarm set points, thermocouple type, temperature units, Trigger level,

Pre-Trigger and Post-Trigger scan interval, Trigger mode, SRQ mask, scan count, Pre-Trigger
count, digital input, digital output, real time settings, data output format, and terminators.

Data Transfer Speed:

Up to >300 Kbytes/s.

Connector:

Standard IEEE 488 connector with metric studs.

RS-232/RS-422 Serial Interface

CAUTION

CAUTION

CAUTION

CAUTION

The RS-232/RS-422 terminal is only for connecting devices having signals at serial
communications levels.

Installation Category:

For CE:

Category 1.

Baud Rates:

300, 600, 1200, 2400, 4800 and 9600.

Data Bits:

8.

Stop Bits:

1.

Parity:

Even, Odd, None.

Handshaking:

RTS/CTS, XON/XOFF (for ASCII transmissions only).

Connector:

Male DB-9.

«
...
23
24
25
26
27
...
»

Содержание MultiScan 1200













































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды