manualshive.com logo in svg

IOtech MultiScan 1200, Руководство пользователя

Поделиться
Скачать
IOtech MultiScan 1200 Скачать руководство пользователя страница 238

228     Chapter 14: System Calibration

TempScan / MultiScan User's Manual

Calibration of Master Chassis

Note:

The following text discusses the 

traditional manual method

 of calibration.  But if you have

access to a PC with Windows 3.X or Windows 95, we strongly suggest using ScanCal.  For
information on the software-automated method of calibration using ScanCal, see chapter

ScanCal

.

Note:

Prior to each calibration session, disable calibration protection by setting the rear panel DIP
microswitch 9 to the up (

1

) position.  Then enable 

Calibration Mode

 via the 

Enter Calibration

Mode

 (

K

) command with a valid password.  If the default calibration password has not been

changed, enter 

K12345

.

Note:

At the end of each calibration session, disable 

Calibration Mode

 with the 

End Calibration

Mode

 (

E

) command.  Then re-enable calibration protection by resetting DIP microswitch 9 to

the down (

0

) position.

Содержание MultiScan 1200













































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды