manualshive.com logo in svg

IOtech MultiScan 1200, Руководство пользователя

Поделиться
Скачать
IOtech MultiScan 1200 Скачать руководство пользователя страница 104

94     Chapter 8: ChartView & ChartView Plus

TempScan / MultiScan User's Manual

A 

Manual Chart Creation, Create Charts

 button allows you to bypass the 

Chart Setup Wizard

 and

enter a manual mode.  This option makes use of 

ChartView’s

 Display Configuration feature (see page

63).  Manual chart creation allows you to vary the number of assigned channels per chart, as well as
vary the number of charts per group.

Chart Setup Wizard, Simple Mode

Chart Setup Wizard

, Automatic Setup Options

Setup Type

Group Setup
(for Chart Groups)

Chart Setup

Channel Setup

Simple

1 group only

Up to 16 charts

1 channel per chart

Moderate

1

1 group only

Up to 16 charts

Up to 4 overlapping channels per chart

Advanced

1

Up to 64 groups

Up to 16 charts per group

Up to 4 overlapping channels per chart

Note

1

:

  Moderate and Advanced modes of Automatic Chart Creation are only available with 

ChartView

 

Plus

.  The

standard 

ChartView

 program allows for 1 chart group only, and does not permit overlapping channels.

Note

2

:

  The 

Manual Chart Creation, Create Charts

 button (above figure) allows you to exit the 

Chart Setup

Wizard

 and enter a manual create chart display mode.

Automatic Chart Creation with Wizard

The previous figure shows the Simple mode dialog box for Automatic Chart Creation.  The following
figures show the Moderate and Advanced mode dialog boxes (available only with 

ChartView

 

Plus

).

Dialog Boxes for Moderate and Advanced Modes of Automatic Chart Creation, ChartView Plus Only

Содержание MultiScan 1200













































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды