manualshive.com logo in svg

IOtech MultiScan 1200, Руководство пользователя

Поделиться
Скачать
IOtech MultiScan 1200 Скачать руководство пользователя страница 343

TempScan / MultiScan User's Manual

Chapter 16: API Command Reference     333

* 

U15

:  Query the product information.  This request responds with the current

TempScan/1100 or MultiScan/1200 product information including version levels.

* 

U16

:  Query the measuring mode parameters (MultiScan/1200 only).  For the

MultiScan/1200 only, this request is equivalent to the following string of measuring mode
queries: 

M#?F#?W#?

  Consequently, this request responds with the following measuring

mode data in their respective forms:

M#mode F#freq W#wt

* 

U17

:  Query the Root Mean Square (RMS) value (MultiScan/1200 only).  For

the MultiScan/1200 only, this request responds with the Root Mean Square (RMS) value
computed from the last-completed acquisition in single-channel high-speed burst mode.  For
more information, see section 

Measuring Modes (MultiScan/1200 Only)

 in the chapter

System Configuration

.

* 

U18

:  Query the acquisition states and various system flags.  This request

responds with an integer 

nnn

 of the form 

000 

≤≤≤≤

 nnn 

≤≤≤≤

 255

, where the separate values are as follows,

and multiple values are summed.  The 

U18

 Bits 7 through 4 respond with the following individual values:

128

 - Acquisition Block Available (Bit 7)

032

 - Not used.

064

 - Power up under default configuration

(Bit 6). Otherwise, power up under the
last configuration.

016

 - Scan Alarm Stamping Enabled (Bit 4)

Meanwhile, the 

U18

 Bits 3 and 2 respond with the following combined values:

012

 - Not used.

004

 - Absolute Scan Time Stamping Enabled

(Bit 2 only)

008

 - Relative Scan Time Stamping

Enabled (Bit 3 only)

000

 - Scan Time Stamping Not Enabled

(Neither Bits 3 nor 2)

Lastly, the 

U18

 Bits 1 and 0 respond with the following combined values:

003

 - Acquiring Post-Stop Scan Data

(Both Bits 1 and 0)

001

 - Armed – Acquisition is armed and may be

acquiring Pre-Trigger Scan Data (Bit 0 only)

002

 - Acquiring Post-Trigger Scan Data

(Bit 1 only)

000

 - Idle – No acquisition is armed or acquiring any

scan data (Neither Bit 1 nor Bit 0)

Note:  

Except for calibration errors, any other error conditions are cleared after the status string is read by the

controller.  Meanwhile, calibration errors are cleared when the unit is calibrated.

Note:

  Status strings are returned when the unit is next addressed to TALK.  If the unit is configured to Trigger on

TALK, requesting a status report will not cause the unit to trigger.

EXAMPLES

Refer to the EXAMPLES section for each of the following commands:

*K - 

Change Calibration Keyword

C  - 

Configure Channels

C# - 

Select Card

F  - 

Set Data Format

K  - 

Enter Calibration Mode

Q  - 

Set Query Terminator

X  - 

Execute

Y  - 

Set Counts

Содержание MultiScan 1200













































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды