manualshive.com logo in svg

IOtech MultiScan 1200, Руководство пользователя

Поделиться
Скачать
IOtech MultiScan 1200 Скачать руководство пользователя страница 139

TempScan / MultiScan User's Manual

Chapter 9: TempView     129

TempView Charts & Meters Windows

As with the 

TempView Main Window

 figure, refer to these 

TempView Charts & Meters Windows

figures as often as necessary.  The items labelled by the lettered and numbered circles are identified in
the two respective tables.

Items labelled by the lettered circles (F to I) are identified in the table below.

TempView Charts Window Areas

Items labelled by the lettered circles (F to H) are identified in the table below.

TempView Bar Graph Meters Window Areas

Содержание MultiScan 1200













































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды