manualshive.com logo in svg

IOtech MultiScan 1200, Руководство пользователя

Поделиться
Скачать
IOtech MultiScan 1200 Скачать руководство пользователя страница 29

TempScan / MultiScan User's Manual

Chapter 2: TempScan/1100 & MultiScan/1200     19

WARNING

WARNING

WARNING

WARNING

Never disassemble the case while it is connected to the AC power line!  Internal

voltage potentials exist which could cause bodily injury or death!

WARNING

WARNING

WARNING

WARNING

Never disconnect the AC power line from the TempScan/1100 or MultiScan/1200

while its scanning cards are connected to an external device!  Common mode
voltage potentials exceeding 60 VDC or 30 Vrms at the terminals, may exist which
could cause bodily injury or death!

Note:

If disassembly or disconnections are necessary, first turn off the power, then disconnect the
scanning cards, next disconnect the AC power line, and then any other cables, prior to unit
disassembly.

To Change the Serial Configuration

1.

 

Turn off the power, disconnect the scanning cards, the power line cord, then all other cables from
the unit.  For more information, see section 

Disconnecting & Reconnecting the System During

Setup

 on page 6.

2.

 

Place the unit on a flat surface.  Remove the six screws on top of the case.  Remove the top cover.

3.

 

The serial port is capable of operating in RS-232 or RS-422 mode.  This selection is done via a set
of hardware jumpers located on the main board behind the serial connector.  A 12-position jumper
plug must be inserted in one of the two available positions for proper operation (across JP11 and
JP12 for RS-232, across JP12 and JP13 for RS-422).  These jumpers are factory set for RS-232 as
shown in the figure.  To reconfigure the serial port for RS-422 operation, remove the jumper plug
and reinsert it into the lower 2 rows of jumpers.

Содержание MultiScan 1200













































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды