IOtech MultiScan 1200 Скачать руководство пользователя страница 253

Страница: 253 / 364

TempScan / MultiScan User's Manual

Chapter 15: Program Examples 243

MultiScan/1200

Example 15d. HLL48.BAS Program

(1)

CLS : PRINT “The MultiScan/1200 is resetting...”
PRINT #1, “OUTPUT 07;*RX”

(3)

SLEEP 4

(4)

WHILE (S% AND 4) = 0

PRINT #1, “SPOLL 07"
INPUT #2, S%

(7)

WEND

(8)

PRINT #1, “OUTPUT 07;M#0X”

(9)

PRINT #1, “OUTPUT 07;W#32X”

(10)

PRINT #1, “OUTPUT 07;C1-24,3X”

(11)

PRINT #1, “OUTPUT 07;C25-48,14X”

(12)

PRINT #1, “OUTPUT07;Y1,0,0X”

(13)

PRINT #1, “OUTPUT07;T1,1,0,0X"

(14)

PRINT “The MultiScan/1200 is collecting HLL data for all 48 channels”
PRINT “Hit a key to start or stop retrieving HLL data...”

(16)

WHILE INKEY$ = “”: WEND

(17)

WHILE INKEY$ = “”

PRINT #1, “OUTPUT 07;U4X”
PRINT #1, “ENTER 07"
LINE INPUT #2, U$

(21)

FOR i = 1 TO 24

PRINT “High, Low and Last readings of Channel”; i
PRINT MID$(U$, (i * 66) - 65, 66)

NEXT i

(25)

FOR i = 1 TO 24

PRINT “High, Low and Last readings of Channel”; i + 24
PRINT MID$(U$, (24 * 66) + (i * 78) - 77, 78)

NEXT i

(29)

WEND

This program is

HLL48.BAS

in the

\EXAMPLES\

subdirectory. It will configure 24 thermocouple and

24 volts channels, collect the High/Low/Last (HLL) Registers data, and post it on the screen.

•

Lines 1-3:

Although not necessary, it is good practice to reset the MultiScan/1200 at the start of

your application by sending the

Reset

Power-On

(

) command. Wait a few seconds.

•

Lines 4-7:

To be certain that the reset was successful and the device is ready, Serial Poll the device

until the proper status is returned.

•

Lines 8-9:

The first thing necessary to start scanning is to setup the measuring mode. In this case,

the MultiScan/1200 will be setup for line-cycle integration / high-speed multi-channel mode.

•

Lines 10-11:

The

Configure Channels

(

) command will be used once to configure a range of

channels from 1 to 24 as Type T thermocouples, and used again to configure a range of channels
from 25 to 48 as

10 volts DC inputs.

•

Lines 12-13:

Program for one

Pre-Trigger

scan via the

Set Counts

(

) command. Then program

the

Trigger

(trigger start event) and

Stop

(trigger stop event) via the

Set Trigger Configuration

(

)

command to arm the acquisition. Telling the MultiScan/1200 to start acquiring data is the last
thing necessary to start scanning. Since the MultiScan/1200 does not scan channels until an
acquisition is armed, arming an acquisition with one

Pre-Trigger

scan allows valid HLL data to be

read.

•

Lines 14-16:

The next three lines tell you to hit a key to start the acquisition. The program will

not proceed until a key is pressed.

Содержание MultiScan 1200













































































































































































































































































































































































Результаты поиска

Содержание MultiScan 1200

Отзывы:

Бренды по названию

Популярные бренды

IOtech MultiScan 1200, Руководство пользователя

Результаты поиска

Содержание MultiScan 1200

Отзывы:

Бренды по названию

Популярные бренды