manualshive.com logo in svg

IOtech MultiScan 1200, Руководство пользователя

Поделиться
Скачать
IOtech MultiScan 1200 Скачать руководство пользователя страница 5

TempScan / MultiScan User's Manual

i

Introduction to this Manual

This manual supersedes previous revisions of the 

TempScan/1100 User’s Manual

 and the

MultiScan/1200 User's Manual

.  The material in this manual discusses specific high-speed temperature

and voltage instruments and their accompanying Windows-based application software.  This material is
divided into the following sections:

Section I:  System Overview

•

 

Chapter 1: System Overview

 

gives a general description of both the hardware and software

products available for the TempScan/1100 or MultiScan/1200 system.  The hardware products
discussed include not only the master units, but also their related expansion units, their optional
scanning cards, and their accessories.  The software products discussed include the Windows-
based applications TempView, PostView, ScanCal, and third-party software accessories.

Section II:  Hardware Guides

This section gives a more-detailed description of each of the hardware products available for the
TempScan/1100 or MultiScan/1200 system.

•

 

Chapter 2: TempScan/1100 & MultiScan/1200

 

provides a detailed discussion of the master units,

their features, front and rear panel descriptions, and necessary hardware configurations.  Both
IEEE 488 and RS-232/RS-422 interfaces are covered.

•

 

Chapter 3: Exp/10A Expansion Unit

 

provides a detailed discussion of this two-slot expansion

unit, its features, front and rear panel descriptions, and necessary hardware configurations.

•

 

Chapter 4: Exp/11A Expansion Unit

 

provides a detailed discussion of this ten-slot expansion unit,

its features, front and rear panel descriptions, and necessary hardware configurations.

•

 

Chapter 5: TempScan/1100 Scanning Cards

 

discusses the three scanning card options available

to the TempScan/1100 unit: The TempTC/32B thermocouple scanning card, the TempV/32B volts
scanning card, and the TempRTD/16B RTD scanning card.

•

 

Chapter 6: MultiScan/1200 Scanning Cards

 

discusses the two scanning card options available to

the MultiScan/1200 unit: The MTC/24 thermocouple/volt scanning card and the MHV/24 high-
voltage scanning card.

•

 

Chapter 7: Power & Assembly

 

provides detailed instructions on line-voltage selection and fuse

replacement, rack-mount and bench-top installation, as well as power-up activation.

Section III:  Software Guides

This section gives a more-detailed description of each of the software products included with the
TempScan/1100 or MultiScan/1200 package.

•

 

Chapter 8: ChartView 

discusses the ready-to-use Windows-based data-logging software that

features the stripchart-style graphical interface designed for users new to this kind of software, and
for users with more-powerful less-resource-limited PC systems.  The various windows, toolbar
buttons and menu items are described and explained.

•

 

Chapter 9: TempView

 

discusses the ready-to-use Windows-based data-logging software that

features the spreadsheet-style graphical interface designed for users already familiar with earlier
versions of TempView, and for users with less-powerful resource-limited PC systems.  The various
windows, toolbar buttons and menu items are described and explained.

•

 

Chapter 10: PostView

 

discusses the Windows-based post-acquisition data-viewing software which

comes as a companion to the ChartView or TempView software. 

 

The various display features of

this viewing program are described and explained.

•

 

Chapter 11: ScanCal 

discusses the Windows-based auto-calibration software which also comes as

a companion to the ChartView or TempView software.  The easy-to-use features of this program
are described and explained.

Содержание MultiScan 1200













































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды