manualshive.com logo in svg

IOtech MultiScan 1200, Руководство пользователя

Поделиться
Скачать
IOtech MultiScan 1200 Скачать руководство пользователя страница 269

TempScan / MultiScan User's Manual

Chapter 15: Program Examples     259

The following program is 

ALAR2SRQ.BAS

 in the 

\EXAMPLES\

 subdirectory.  It will set up the alarm

system of the MultiScan/1200, and then it will use the IEEE 488 Service Request signal to
asychronously service the event.

•

 

Lines 1-3:

 Although not necessary, it is good practice to reset the MultiScan/1200 at the start of

your application by sending the 

Reset

 

Power-On 

(

*R

) command.  Wait a few seconds.

•

 

Lines 4-8:

 To be certain that the reset was successful and the device is ready, Serial Poll the device

until the proper status is returned.

•

 

Lines 9-10:

 The PC/IEEE 488 controller interface and driver software provides a means for

QuickBASIC to asynchronously service the IEEE 488 

SRQ

 interrupt through its 

ON PEN GOSUB

command.  When an 

SRQ

 is detected by the controller, program control is automatically vectored

to the subroutine named in the 

ON PEN GOSUB

 command.  To activate this feature in the 

IEEE 488

driver, the command 

ARM SRQ

 must be sent to the driver.

•

 

Line 11: 

The 

Set SRQ Mask

 (

M

) command 

M1

 instructs the MultiScan/1200 unit to assert the 

SRQ

signal when it is in an alarm state.

•

 

Lines 12-13:

 The first thing necessary to start scanning is to setup the measuring mode.  In this

case, the MultiScan/1200 will be setup for line-cycle integration / high-speed multi-channel mode.

•

 

Lines 14-15:

 The 

Configure Channels

 (

C

) command will be used once to configure a range of

channels from 1 to 24 as Type T thermocouples, and used again to configure Channels 1 and 2
such that levels above 25 or below 1 will cause a system alarm.  Once the 

C

 command is issued, the

MultiScan/1200 will be completely armed for alarming.  Since the 

M1

 command has already been

issued, this will also result in an IEEE 488 

SRQ

 assertion.

•

 

Line 16-17:

 In addition to causing an internal system alarm state, the alarm conditions can also be

attached to any one of the 32 digital output lines.  The 

Assign Digital Alarm Output

 (

A

) command

will be used to assign input Channel 1 to digital alarm Output 1, and Channel 2 to Output 2,
individually.

•

 

Lines 18-19:

 Program for one 

Pre-Trigger

 scan via the 

Set Counts

 (

Y

) command.  Then program

the 

Trigger 

(trigger start event) and 

Stop 

(trigger stop event) via the 

Set Trigger Configuration

 (

T

)

command to arm the acquisition.

•

 

Lines 20-37:

 This example now processes a loop that is waiting for a key press in order to exit.  If

an 

SRQ

 is detected by the IEEE 488 driver, program control will be automatically vectored to the

AlarmHandler

 subroutine, then returned to the wait loop again.  In the alarm service routine, the

MultiScan/1200 unit is first Serial Polled (

SPOLL

ed) to clear the 

SRQ

 signal.  The 

Set Digital

Outputs

 (

O

) command 

O?

 will be used to query the status of the digital output lines.  In turn, the

channel number that is in the alarm state can be identified.

Содержание MultiScan 1200













































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды